參數資料
型號： MAX9791AETI+
廠商： Maxim Integrated Products
文件頁數： 18/34頁
文件大?。?/td> 0K
描述： IC AMP AUDIO 2.2W STER D 28TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 75
系列： DirectDrive®
類型： D 類
輸出類型： 2-通道（立體聲）帶立體聲耳機和超低音器
在某負載時最大輸出功率 x 通道數量： 2.2W x 2 @ 4 歐姆; 180mW x 2 @ 32 歐姆
電源電壓： 4.5 V ~ 5.5 V
特點： 消除爆音，LDO，短路保護和熱保護，關機
安裝類型： 表面貼裝
供應商設備封裝： 28-TQFN-EP（5x5）
封裝/外殼： 28-WFQFN 裸露焊盤
包裝： 管件
MAX9791/MAX9792
Windows Vista-Compliant Class D Speaker
Amplifiers with DirectDrive Headphone Amplifiers
______________________________________________________________________________________
25
Component Selection
Speaker Amplifier Power-Supply Input (PVDD)
PVDD powers the speaker amplifiers. PVDD ranges
from 2.7V to 5.5V. AVDD and PVDD must be tied
together. If LDO is enabled, set AVDD and PVDD as
specified in the Line Regulation row of the
Electrical
Characteristics table. Bypass PVDD with a 0.1F
capacitor to PGND. Apply additional bulk capacitance
at the device if long input traces between PVDD and
the power source are used.
Headphone Amplifier Power-Supply Input
(HPVDD and CPVSS)
The headphone amplifiers are powered from HPVDD
and CPVSS. HPVDD is the positive supply of the head-
phone amplifiers and ranges from 2.7V to 5.5V. Bypass
HPVDD with a 10F capacitor to PGND. CPVSS is the
negative supply of the headphone amplifiers. Bypass
CPVSS with a 1F capacitor to PGND. The charge
pump inverts the voltage at HPVDD, and the resulting
voltage appears at CPVSS. A 1F capacitor should be
connected between C1N and C1P.
Positive Power Supply and LDO Input (AVDD)
The internal LDO and the remainder of the device are
powered by AVDD. AVDD ranges from 2.7V to 5.5V.
AVDD and PVDD must be tied together. If LDO is
enabled, set AVDD and PVDD as specified in LDO line
regulation. Bypass AVDD with a 0.1F capacitor to
GND and two 1F capacitors to GND. Note additional
bulk capacitance is required at the device if long input
traces between AVDD and the power source are used.
Input Filtering
The input capacitor (CIN_), in conjunction with the ampli-
fier input resistance (RIN_), forms a highpass filter that
removes the DC bias from the incoming signal. The AC-
coupling capacitor allows the amplifier to bias the signal
to an optimum DC level. Assuming zero source imped-
ance, the -3dB point of the highpass filter is given by:
RIN_ is the amplifier’s external input resistance value.
Choose CIN_ such that f-3dB is well below the lowest
frequency of interest. Setting f-3dB too high affects
the amplifier’s low frequency response. Use capaci-
tors with adequately low-voltage coefficients (see
Figure 12). Capacitors with higher voltage coeffi-
cients, such as ceramics, result in increased distor-
tion at low frequencies.
Charge-Pump Capacitor Selection
Use capacitors with an ESR less than 100m
for opti-
mum performance. Low ESR ceramic capacitors mini-
mize the output resistance of the charge pump. For
best performance over the extended temperature
range, select capacitors with an X7R dielectric.
Flying Capacitor (C1)
The value of the flying capacitor (C1) affects the load
regulation and output resistance of the charge pump. A
C1 value that is too small degrades the device’s ability
to provide sufficient current drive, which leads to a loss
of output voltage. Connect a 1F capacitor between
C1P and C1N.
f
RC
dB
IN
-3
1
2
=
π
__
INPUT COUPLING CAPACITOR-INDUCED THD+N
vs. FREQUENCY (HEADPHONE MODE)
FREQUENCY (kHz)
THD+N
(dBFS)
100
-90
-80
-70
-60
-50
-100
10
1000
0603 10V X5R 10% 1
F
0805 50V X7R 10% 1
F
VOUT - -3dBFS
FS = 1VRMS
RL =32
0603 10V X7R 10% 1
F
0402 6.3V X5R 10% 1
F
Figure 12. Input Coupling Capacitor-Induced THD+N vs.
Frequency
SPEAKER RF IMMUNITY
vs. FREQUENCY
FREQUENCY (MHz)
AMPLITUDE
(dBV)
2500
2000
1500
1000
500
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
-130
0
3000
RIGHT
LEFT
Figure 13. Speaker RF Immunity
相關PDF資料
PDF描述
GE330K CAP CER 33PF 50V 10% RADIAL
GE102K CAP CER 1000PF 50V 10% RADIAL
GE101K CAP CER 100PF 50V 10% RADIAL
VJ1808A102JXGAT CAP CER 1000PF 1KV 5% NP0 1808
MAX9710ETP+ IC AMP AUDIO PWR 3W STER 20TQFN
相關代理商/技術參數
參數描述
MAX9791AETI+ 功能描述:音頻放大器 Windows Vista Class D Speaker Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9791AETI+T 功能描述:音頻放大器 Windows Vista Class D Speaker Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9791AEVKIT+ 功能描述:音頻放大器 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9791BETI+ 功能描述:音頻放大器 Windows Vista Class D Speaker Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9791BETI+T 功能描述:音頻放大器 Windows Vista Class D Speaker Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*