- 您現在的位置：買賣IC網 > PDF目錄10340 > MAX9776EBX+TG45 (Maxim Integrated Products)IC AMP AUDIO PWR 1.5W MONO 36WLP PDF資料下載
參數資料
| 型號： | MAX9776EBX+TG45 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/38頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 1.5W MONO 36WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 1.5W x 1 @ 4 歐姆; 60mW x 2 @ 16 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 36-WLP |
| 封裝/外殼： | 36-UFBGA，WLCSP |
| 包裝： | 帶卷 (TR) |
| 配用： | MAX9776EVKIT+-ND - EVALUATION KIT FOR MAX9776 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
MAX9775/MAX9776
2 x 1.5W, Stereo Class D Audio Subsystem
with DirectDrive Headphone Amplifier
22
______________________________________________________________________________________
Filterless Modulation/Common-Mode Idle
The MAX9775/MAX9776 use Maxim’s unique modula-
tion scheme that eliminates the LC filter required by tra-
ditional Class D amplifiers, improving efficiency,
reducing component count, conserving board space
and system cost. Conventional Class D amplifiers out-
put a 50% duty-cycle square wave when no signal is
present. With no filter, the square wave appears across
the load as a DC voltage, resulting in finite load current,
increasing power consumption, especially when idling.
When no signal is present at the input of the
MAX9775/MAX9776, the outputs switch as shown in
Figure 4. Because the MAX9775/MAX9776 drive the
speaker differentially, the two outputs cancel each
other, resulting in no net idle mode voltage across the
speaker, minimizing power consumption.
DirectDrive
Traditional single-supply headphone amplifiers have
outputs biased at a nominal DC voltage (typically half
the supply) for maximum dynamic range. Large cou-
pling capacitors are needed to block this DC bias from
the headphone. Without these capacitors, a significant
amount of DC current flows to the headphone, resulting
in unnecessary power dissipation and possible dam-
age to both headphone and headphone amplifier.
Maxim’s DirectDrive architecture uses a charge pump to
create an internal negative supply voltage. This allows the
headphone outputs of the MAX9775/MAX9776 to be
biased at GND, almost doubling dynamic range while
operating from a single supply. With no DC component,
there is no need for the large DC-blocking capacitors.
Instead of two large (220F, typ) tantalum capacitors, the
MAX9775/MAX9776 charge pump requires two small
ceramic capacitors, conserving board space, reducing
cost, and improving the frequency response of the head-
phone amplifier. See the Output Power vs. Load
Resistance and Charge-Pump Capacitor Size graph in
the
Typical Operating Characteristics for details of the
possible capacitor sizes. There is a low DC voltage on
the amplifier outputs due to amplifier offset. However, the
offset of the MAX9775/MAX9776 is typically 1.4mV,
which, when combined with a 32Ω load, results in less
than 44nA of DC current flow to the headphones.
In addition to the cost and size disadvantages of the
DC-blocking capacitors required by conventional head-
phone amplifiers, these capacitors limit the amplifier’s
low-frequency response and can distort the audio sig-
nal. Previous attempts at eliminating the output-cou-
pling capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raises some issues:
1) The sleeve is typically grounded to the chassis.
Using the midrail biasing approach, the sleeve must
be isolated from system ground, complicating prod-
uct design.
2) During an ESD strike, the driver’s ESD structures are
the only path to system ground. Thus, the amplifier
must be able to withstand the full ESD strike.
3) When using the headphone jack as a lineout to
other equipment, the bias voltage on the sleeve may
conflict with the ground potential from other equip-
ment, resulting in possible damage to the amplifiers.
VIN = 0V
OUT-
OUT+
VOUT+ - VOUT- = 0V
Figure 4. Outputs with No Input Signal
相關PDF資料 |
PDF描述 |
|---|---|
| MS27508E18B11S | CONN RCPT 11POS BOX MNT W/SCKT |
| MS3106F16-10P | CONN PLUG 3POS STRAIGHT W/PINS |
| MAX13330GEE/V+T | IC AMP STEREO HEADPHONE 16-QSOP |
| LTC2480HDD#TRPBF | IC ADC DELTA SIGMA 16BIT 10DFN |
| MAX9789BETJ+T | IC AMP AUDIO 2W STER AB 32TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9776ETJ+ | 功能描述:音頻放大器 2 x 1.5W Stereo Class D Subsystem RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9776ETJ+T | 功能描述:音頻放大器 2 x 1.5W Stereo Class D Subsystem RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9776EVKIT+ | 功能描述:音頻 IC 開發工具 MAX9776 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX9777ETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9777ETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。