- 您現在的位置：買賣IC網 > PDF目錄10265 > MAX9750CETI+C2U (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF資料下載
參數資料
| 型號： | MAX9750CETI+C2U |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 標準包裝： | 60 |
| 系列： | DirectDrive® |
| 類型： | AB 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.2W x 2 @ 3 歐姆; 110mW x 2 @ 16 歐姆 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 特點： | 消除爆音，短路保護和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MAX9750/MAX9751/MAX9755
2.6W Stereo Audio Power Amplifiers and
DirectDrive Headphone Amplifiers
22
______________________________________________________________________________________
reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output power levels. See the Output Power
vs. Charge-Pump Capacitance and Load Resistance
graph in the
Typical Operating Characteristics.
CPVDD Bypass Capacitor (C3)
The CPVDD bypass capacitor (C3) lowers the output
impedance of the power supply and reduces the
impact of the MAX9750/MAX9751/MAX9755’s charge-
pump switching transients. Bypass CPVDD with C3, the
same value as C1, and place it physically close to
CPVDD and PGND (refer to the MAX9750 Evaluation Kit
for a suggested layout).
Powering Other Circuits from a
Negative Supply
An additional benefit of the MAX9750/MAX9751/
MAX9755 is the internally generated negative supply volt-
age (CPVSS). CPVSS is used by the MAX9750/
MAX9751/MAX9755 to provide the negative supply for
the headphone amplifiers. It can also be used to power
other devices within a design. Current draw from CPVSS
should be limited to 5mA, exceeding this affects the oper-
ation of the headphone amplifier. A typical application is
a negative supply to adjust the contrast of LCD modules.
When considering the use of CPVSS in this manner,
note that the charge-pump voltage of CPVSS is roughly
proportional to CPVDD and is not a regulated voltage.
The charge-pump output impedance plot appears in
the
Typical Operating Characteristics.
Layout and Grounding
Proper layout and grounding are essential for optimum
performance. Use large traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance, as well as route head away
from the device. Good grounding improves audio per-
formance, minimizes crosstalk between channels, and
prevents any switching noise from coupling into the
audio signal. Connect CPGND, PGND and GND
together at a single point on the PC board. Route
CPGND and all traces that carry switching transients
away from GND, PGND, and the traces and compo-
nents in the audio signal path.
Connect all components associated with the charge
pump (C2 and C3) to the CPGND plane. Connect VSS
and CPVSS together at the device. Place the charge-
pump capacitors (C1, C2, and C3) as close to the
device as possible. Bypass HPVDD and PVDD with a
0.1F capacitor to GND. Place the bypass capacitors
as close to the device as possible.
Use large, low-resistance output traces. As load imped-
ance decreases, the current drawn from the device out-
puts increase. At higher current, the resistance of the
output traces decrease the power delivered to the load.
For example, when compared to a 0
Ω trace, a 100mΩ
trace reduces the power delivered to a 4
Ω load from
2.1W to 2W. Large output, supply, and GND traces also
improve the power dissipation of the device.
The MAX9750/MAX9751/MAX9755 thin QFN package
features an exposed thermal pad on its underside. This
pad lowers the package’s thermal resistance by provid-
ing a direct heat conduction path from the die to the
printed circuit board. Connect the exposed thermal
pad to GND by using a large pad and multiple vias to a
GND plane on the bottom of the PCB.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-22H-IW-S | CONVERTER MOD DC/DC 52V 100W |
| VE-262-MY | CONVERTER MOD DC/DC 15V 50W |
| MAX9751ETI+ | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| VE-262-IU-S | CONVERTER MOD DC/DC 15V 200W |
| MAX9750CETI+ | IC AMP AUDIO PWR 2.6W AB 28TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9750CEUI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9751ETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9751ETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9751EUI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9752AETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。