- 您現在的位置：買賣IC網 > PDF目錄384714 > MAX968EUA (MAXIM INTEGRATED PRODUCTS INC) Single/Dual/Quad, Micropower, Ultra-Low-Voltage, Rail-to-Rail I/O Comparators PDF資料下載
參數資料
| 型號： | MAX968EUA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Single/Dual/Quad, Micropower, Ultra-Low-Voltage, Rail-to-Rail I/O Comparators |
| 中文描述： | DUAL COMPARATOR, 15000 uV OFFSET-MAX, 20000 ns RESPONSE TIME, PDSO8 |
| 封裝： | MO-187C-AA, MICRO MAX PACKAGE-8 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 116K |
| 代理商： | MAX968EUA |
M
Single/Dual/Quad, Micropower,
Ultra-Low-Voltage, Rail-to-Rail I/O Comparators
function below about 1.5V, although the comparators
typically continue to operate with a supply voltage as
low as 1V. At low supply voltages (<1.6V), the input
common-mode range remains rail-to-rail, but the com-
parator’s output sink capability is reduced and propa-
gation delay increases (see
Typical Operating
Characteristics
).
Figure 1 shows a typical comparator application that
monitors V
CC
at 1.6V. Resistor divider R1/R2 sets the
voltage trip point (V
TRIP
) at 1.6V. As V
CC
drops below
1.6V and approaches 1V, the reference voltage typical-
ly falls below the divider voltage (V+). This causes the
comparator output to change state. If OUT’s state must
be maintained under these conditions, a latching circuit
is required.
Comparator Output
The MAX965–MAX970 contain a unique slew-rate-
controlled output stage capable of rail-to-rail operation
with an external pull-up resistor. Typical comparators
consume orders of magnitude more current during
switching than during steady-state operation. With the
MAX965 family of comparators, during an output transi-
tion from high to low, the output slew rate is limited to
minimize switching current.
V oltage Referenc e
With V
CC
greater than 1.6V but less than 5.5V, the inter-
nal 1.235V bandgap reference is ±1.5% accurate over
the commercial temperature range and ±2.5% accu-
rate over the extended temperature range. The REF
output is typically capable of sourcing 50μA. To reduce
reference noise or to provide noise immunity, bypass
REF with a capacitor (0.1nF to 0.1μF).
Noise Considerations
The comparator has an effective wideband peak-to-
peak noise of around 10μV. The voltage reference has
peak-to-peak noise approaching 1.0mV with a 0.1μF
bypass capacitor. Thus, when a comparator is used
with the reference, the combined peak-to-peak noise is
about 1.0mV. This, of course, is much higher than the
individual components’ RMS noise. Avoid capacitive
coupling from any output to the reference pin. Crosstalk
can significantly increase the references’ actual noise.
__________Applic ations Information
Hysteresis
Many comparators oscillate in the linear region of oper-
ation because of noise or undesired parasitic feed-
back. This tends to occur when the voltage on one
input is equal or very close to the voltage on the other
input. The MAX965–MAX970 have internal hysteresis to
counter parasitic effects and noise. In addition, with the
use of external resistor, the MAX965/MAX967/
MAX968/MAX969’s hysteresis can be programmed to
as much as ±50mV (see the section
Adding Hysteresis
to the MAX965/MAX967/MAX968/MAX969
).
The hysteresis in a comparator creates two trip points:
one for the rising input voltage and one for the falling
input voltage (Figure 2). The difference between the trip
points is the hysteresis. When the comparator’s input
voltages are equal, the hysteresis effectively causes
one comparator input voltage to move quickly past the
other, thus taking the input out of the region where
oscillation occurs.
THRESHOLDS
OUT
IN-
IN+
V
HB
HYSTERESIS
BAND
V
REF
- V
HYST
Figure 2. Threshold Hysteresis Band
REF
GND
V
CC
V
TRIP
= 1.22
+ 1
V
CC
V
REF
OUT
R1
47k
R2
150k
V+
V
CC
V+
t
1.6V
1.0V
100k
MAX965
R1
R2
R1 =
x R2
- 1
V
TRIP
1.22
Figure 1. Operation below 1.6V
_______________________________________________________________________________________
9
相關PDF資料 |
PDF描述 |
|---|---|
| MAX970 | 8-Bit Bus-Interface Flip-Flops With 3-State Outputs 24-CDIP -55 to 125 |
| MAX970EEE | Single/Dual/Quad, Micropower, Ultra-Low-Voltage, Rail-to-Rail I/O Comparators |
| MAX970ESD | Single/Dual/Quad, Micropower, Ultra-Low-Voltage, Rail-to-Rail I/O Comparators |
| MAX967ESA | Octal Transparent D-type Latches With 3-State Outputs 20-CDIP -55 to 125 |
| MAX968ESA | Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX968EUA+ | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX968EUA+T | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX968EUA-T | 功能描述:校驗器 IC Dual Comparator / Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9691EPA | 功能描述:校驗器 IC Single Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9691EPA+ | 功能描述:校驗器 IC Single Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。