- 您現在的位置：買賣IC網 > PDF目錄385554 > MAX9118EXK (Maxim Integrated Products, Inc.) PLASTIC ENCAPSULATED DEVICES PDF資料下載
參數資料
| 型號： | MAX9118EXK |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | PLASTIC ENCAPSULATED DEVICES |
| 中文描述： | 塑封器件 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 180K |
| 代理商： | MAX9118EXK |
V. Quality Assurance Information
A. Quality Assurance Contacts:
B. Outgoing Inspection Level: 0.1% for all electrical parameters guaranteed by the Datasheet.
0.1% For all Visual Defects.
C. Observed Outgoing Defect Rate: < 50 ppm
D. Sampling Plan: Mil-Std-105D
VI. Reliability Evaluation
A. Accelerated Life Test
The results of the 135
°
C biased (static) life test are shown in
Table 1
. Using these results, the Failure
Rate (
λ
) is calculated as follows:
λ
= 1 = 1.83 (Chi square value for MTTF upper limit)
MTTF
192 x 4389 x 80 x 2
Temperature Acceleration factor assuming an activation energy of 0.8eV
λ
= 13.57 x 10
-9
λ
= 13.57 F.I.T. (60% confidence level @ 25
°
C)
This low failure rate represents data collected from Maxim’s reliability monitor program. In addition to
routine production Burn-In, Maxim pulls a sample from every fabrication process three times per week and subjects
it to an extended Burn-In prior to shipment to ensure its reliability. The reliability control level for each lot to be
shipped as standard product is 59 F.I.T. at a 60% confidence level, which equates to 3 failures in an 80 piece
sample. Maxim performs failure analysis on any lot that exceeds this reliability control level. Attached Burn-In
Schematic (Spec. # 06-5415) shows the static Burn-In circuit. Maxim also performs quarterly 1000 hour life test
monitors. This data is published in the Product Reliability Report (
RR-1M
).
B. Moisture Resistance Tests
Maxim pulls pressure pot samples from every assembly process three times per week. Each lot sample
must meet an LTPD = 20 or less before shipment as standard product. Additionally, the industry standard
85
°
C/85%RH testing is done per generic device/package family once a quarter.
C. E.S.D. and Latch-Up Testing
The CM82-1
die type has been found to have all pins able to withstand a transient pulse of
±
2000V, per Mil-
Std-883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device
withstands a current of
±
250mA.
Jim Pedicord (Reliability Lab Manager)
Bryan Preeshl (Executive Director
)
Kenneth Huening (Vice President)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9124 | Quad LVDS Line Driver |
| MAX9124ESE | Quad LVDS Line Driver |
| MAX9124EUE | Quad LVDS Line Driver |
| MAX9129EUE | Quad Bus LVDS Driver with Flow-Through Pinout |
| MAX912 | Dual, Ultra-Fast, Low-Power, Precision TTL Comparators(雙路超高速,低功耗,精密TTL比較器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9118EXK+ | 制造商:Maxim Integrated Products 功能描述:COMPARATOR SGL R-R O/P 5.5V 5PIN SC-70 - Rail/Tube |
| MAX9118EXK+T | 功能描述:校驗器 IC 1.6V nPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9118EXK-T | 功能描述:校驗器 IC 1.6V nPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9119 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX9119ESA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。