- 您現在的位置：買賣IC網 > PDF目錄385554 > MAX8902A (Maxim Integrated Products, Inc.) Low-Noise 500mA LDO Regulators in a 2mm x 2mm TDFN Package PDF資料下載
參數資料
| 型號： | MAX8902A |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Noise 500mA LDO Regulators in a 2mm x 2mm TDFN Package |
| 中文描述： | 低噪聲500mA LDO穩壓器，2mm x 2mm TDFN封裝 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 277K |
| 代理商： | MAX8902A |
The BP capacitor value can be adjusted from 0.001μF
to 0.1μF, to change the startup slew rate according to
the following formula:
Startup slew rate = (5V / ms) x (0.01μF / C
BP
)
Note that this slew rate applies only at startup, and that
recovery from a short circuit occurs at a slew rate
approximately 500 times slower.
Also note that, being a low-frequency filter node, BP is
sensitive to leakage. BP leakage currents above 10nA
cause measurable inaccuracy at the output and should
be avoided.
Protection Features
The MAX8902A/MAX8902B are fully protected from an
output short circuit by a current-limiting and thermal
overload circuit. If the output is shorted to GND, the
output current is limited to 700mA (typ). Under these
conditions, the part quickly heats up. When the junction
temperature reaches +165°C, a thermal limit circuit
shuts off the output device. When the junction cools to
+150°C, the output turns back on in an attempt to
reestablish regulation. While the fault persists, the out-
put current cycles on and off, as the junction tempera-
ture slews between +150°C and +165°C.
The MAX8902A/MAX8902B are also protected against
reverse current when the output voltage is higher than
the input. In the event that extra output capacitance is
used at the output, a power-down transient at the input
would normally cause a large reverse current through a
conventional regulator. The MAX8902A/MAX8902B
include a reverse voltage detector that trips when IN
drops 10mV below OUT, shutting off the regulator and
opening the PMOS body diode connection, preventing
any reverse current.
Thermal Considerations
The MAX8902A/MAX8902B are packaged in an 8-pin,
2mm x 2mm TDFN package with an exposed paddle.
The exposed paddle is the main path for heat to leave
the IC, and therefore, must be connected to a ground
plane with thermal vias to allow heat to dissipate from
the device. Thermal properties of the IC package are
given in Table 1.
Selecting the Output Voltage (MAX8902A)
The MAX8902A output can be set to one of nine volt-
ages by shorting or opening the SELA and SELB
inputs, as shown in Table 2. SELA and SELB should be
connected to GND, IN, or left unconnected.
Alternatively, they may be driven high, low, or open with
external logic, however, the states of SELA and SELB
are sampled only at startup. The regulation voltage can
be set to a different level by cycling EN or IN momen-
tarily to GND.
Setting the Output Voltage (MAX8902B)
The MAX8902B uses external feedback resistors to set
the output regulation voltage as shown in Figure 3. The
output can be set from 0.6V to 5.3V. Set the lower feed-
back resistor (R2) to 120k
Ω
or less to minimize FB input
bias current error. Then calculate the value of the upper
feedback resistor (R1) as follows:
where V
FB
is the feedback regulation voltage of 0.6V.
Power OK (MAX8902B)
The MAX8902B includes an additional open-drain out-
put,
POK
, that pulls low to indicate the output voltage is
in regulation. During startup,
POK
is high impedance
until the output voltage rises to 91% of its regulation
level. If an overload occurs at the output, or the output
is shutdown,
POK
is high impedance.
R
R
V
V
OUT
FB
1
2
1
=
×
,
M
Low-Noise 500mA LDO Regulators
in a 2mm x 2mm TDFN Package
_______________________________________________________________________________________
7
CONTINUOUS POWER
DISSIPATION
953.5mW DERATE 11.9mW/°C
ABOVE +70°C
θ
JA
*
θ
JC
83.9°C/W
36.6°C/W
Table 1. 2mm x 2mm TDFN Package
Thermal Characteristics
OUTPUT VOLTAGE
1.5V
1.8V
2.0V
2.5V
3.0V
3.1V
3.3V
4.6V
4.7V
SELA STATE
IN
Unconnected
Unconnected
Unconnected
GND
GND
GND
IN
IN
SELB STATE
Unconnected
GND
IN
Unconnected
GND
IN
Unconnected
GND
IN
Table 2. MAX8902A Output Voltages
*
θ
JA
is specified according to the JESD51 standard with the
part mounted on a multilayer PCB.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX890LESA-T | Single Peripheral Driver |
| MAX891LEUA | Single Peripheral Driver |
| MAX891LEUA-T | Single Peripheral Driver |
| MAX892LEUA | Single Peripheral Driver |
| MAX892LEUA-T | Single Peripheral Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8902AATA+ | 制造商:Maxim Integrated Products 功能描述:LDO REGULATORS 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Bulk |
| MAX8902AATA+T | 功能描述:低壓差穩壓器 - LDO 500mA LDO Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX8902AATAT | 制造商:MAXIM/DALLAS 功能描述: |
| MAX8902BATA/V+ | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE 500MA LDO REGULATORS IN A 2MM X 2MM TDFN PACKAGE - Rail/Tube |
| MAX8902BATA/V+T | 功能描述:低壓差穩壓器 - LDO 150mA LDO Linear Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。