- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX8896EREE+T (Maxim Integrated)IC REG TRPL BCK/LINEAR 16UCSP Datasheet資料下載
參數資料
| 型號： | MAX8896EREE+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 13/17頁 |
| 文件大小： | 449K |
| 描述： | IC REG TRPL BCK/LINEAR 16UCSP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 拓?fù)洌?/td> | 降壓（降壓）同步（2），線性（LDO）（1） |
| 功能： | 任何功能 |
| 輸出數： | 3 |
| 頻率 - 開關： | 2MHz |
| 電壓/電流 - 輸出 1： | 0.2 V ~ 1.7 V，700mA |
| 電壓/電流 - 輸出 2： | 3.1V，200mA |
| 電壓/電流 - 輸出 3： | 2.8V，200mA |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFBGA，CSPBGA |
| 供應商設備封裝： | 16-UCSP（4x4） |
| 包裝： | 標準包裝 |
| 其它名稱： | MAX8896EREE+TDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁
Dual PWM Step-Down Converter in a 2mm x
2mm Package for WCDMA PA and RF Power
______________________________________________________________________________________ 13
The OUT2 step-down DC-DC converter operates with
100% duty cycle when the supply voltage approaches
the output voltage. This allows this converter to main-
tain regulation until the input voltage falls below the
desired output voltage plus the dropout voltage specifi-
cation of the converter. During 100% duty cycle opera-
tion, the high-side p-channel MOSFET turns on
constantly, connecting the input to the output through
the inductor. The dropout voltage (V
DO
) is calculated
as follows:
V
DO
= I
LOAD
x (R
P
+ R
L
)
where:
R
P
= internal p-channel MOSFET switch on-resistance
(see Electrical Characteristics)
R
L
= external inductor DC resistance
LDO
The LDO provides 200mA at 2.8V and is designed for
low noise (16礦
RMS
, typ) and high PSRR (65dB, typ).
The LDO is powered from OUT2 (3.1V) and is enabled
or disabled at the same time as OUT2 using RFEN1 or
RFEN2.
LDO Dropout Voltage
The regulators minimum input/output differential (or
dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this determines
the useful end-of-life battery voltage. Because the LDO
uses a p-channel MOSFET pass transistor, the dropout
voltage is drain-to-source on-resistance (R
DS(ON)
) mul-
tiplied by the load current (see the Typical Operating
Characteristics).
Shutdown Mode
Connect PAEN to GND or logic-low to place OUT1 in
shutdown mode. In shutdown, the control circuitry,
internal switching MOSFET, and synchronous rectifier
turn off and LX1 becomes high impedance. Connect
PAEN to IN1, V
CC
, or logic-high for normal operation.
Either RFEN1 or RFEN2 enable OUT2 and the LDO.
Connect RFEN1 and RFEN2 to GND or logic-low to
place OUT2 and the LDO in shutdown mode. In shut-
down, the control circuitry, internal switching MOSFET,
and synchronous rectifier turn off and LX2 and the LDO
output become high impedance. Connect RFEN1 or
RFEN2 to IN2, V
CC
, or logic-high for normal operation.
When PAEN, RFEN1, and RFEN2 are all logic-low, the
MAX8896 enter a very low power state, where the input
current drops to 0.1礎 (typ).
Thermal-Overload Protection
Thermal-overload protection limits total power dissipation
in the MAX8896. If the junction temperature exceeds
+160癈, the MAX8896 turn off, allowing the IC to cool.
The IC turns on and begins soft-start after the junction
temperature cools by 20癈. This results in a pulsed out-
put during continuous thermal-overload conditions.
Applications Information
Inductor Selection
OUT1 operates with a switching frequency of 2MHz and
utilizes a 2.2礖 to 4.7礖 inductor. OUT2 operates with a
switching frequency of 2MHz and utilizes a 2.2礖 induc-
tor. This operating frequency allows the use of physically
small inductors while maintaining high efficiency.
The OUT1 inductors DC current rating only needs to
match the maximum load of the application because
OUT1 features zero current overshoot during startup and
load transients. For optimum transient response and high
efficiency, choose an inductor with DC series resistance
in the 50m&to 150m&range. See Table 1 for suggested
inductors and manufacturers.
Using a larger inductance value reduces the ripple cur-
rent, therefore providing higher efficiency at light load.
Output Capacitor Selection
For OUT1 and OUT2, the output capacitor keeps the
output voltage ripple small and ensures regulation loop
stability. C
OUT
must have low impedance at the switch-
ing frequency. Ceramic capacitors with X5R or X7R
temperature characteristics are highly recommended
due to their small size, low ESR, and small temperature
coefficients. A 4.7礔 capacitor is recommended for
C
OUT1
and 2.2礔 is recommended for C
OUT2
. For opti-
mum load-transient performance and very low output
ripple, the output capacitor value can be increased.
For the LDO, the minimum output capacitance required
is dependent on the load currents. For loads lighter
than 10mA, it is sufficient to use a 0.1礔 capacitor for
stable operation over the full temperature range. With
rated maximum load currents, a minimum of 1礔 is rec-
ommended. Larger value output capacitors further
reduce output noise and improve load-transient
response, stability, and power-supply rejection.
Note that some ceramic dielectrics exhibit large capac-
itance and ESR variation with temperature and DC bias.
Ceramic capacitors with Z5U or Y5V temperature char-
acteristics should be avoided. These regulators are
optimized for ceramic capacitors. Tantalum capacitors
are not recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33232PG | IC PFC CONTROLLER CRM 8DIP |
| MC33260DR2G | IC PFC CONTROLLER DCM 8SOIC |
| MC33262DG | IC PFC CONTROLLER CRM 8SOIC |
| MC33368DR2G | IC PFC CONTROLLER CRM 16SOIC |
| MC33567D-1G | IC REG CTRLR DUAL OUT 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8896EVKIT+ | 功能描述:直流/直流開關轉換器 Dual PWM Step-Down Converter in a 2mm x 2mm Package for WCDMA PA and RF Power RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX8899EVKIT+ | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR MAX8899 - Boxed Product (Development Kits) |
| MAX8899EWZ+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX8899EWZ+T | 制造商:Maxim Integrated Products 功能描述:WCDMA/EDGE/GPRS/GSM/CDMA - Tape and Reel |
| MAX8899EWZ+TCAA | 制造商:Maxim Integrated Products 功能描述:WCDMA/EDGE/GPRS/GSM/CDMA PHONE PMIC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。