- 您現在的位置：買賣IC網 > PDF目錄385551 > MAX812 (Maxim Integrated Products, Inc.) 4-Pin μp Voltage Monitors with Manual Reset Input(4管腳μP電壓監控器,低有效復位輸出) PDF資料下載
參數資料
| 型號： | MAX812 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 4-Pin μp Voltage Monitors with Manual Reset Input(4管腳μP電壓監控器,低有效復位輸出) |
| 中文描述： | 4引腳微處理器電壓監視器，帶有手動復位輸入 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 69K |
| 代理商： | MAX812 |
M
4-Pin μP Voltage Monitors
with Manual Reset Input
_______________________________________________________________________________________
5
______________________________________________________________Pin Desc ription
_______________Detailed Desc ription
Reset Output
A microprocessor’s (μP’s) reset input starts the μP in a
known state. These μP supervisory circuits assert reset
to prevent code execution errors during power-up,
power-down, or brownout conditions.
RESET is guaranteed to be a logic low for V
CC
> 1V.
Once V
CC
exceeds the reset threshold, an internal
timer keeps RESET low for the reset timeout period;
after this interval, RESET goes high.
If a brownout condition occurs (V
CC
dips below the
reset threshold), RESET goes low. Any time V
CC
goes
below the reset threshold, the internal timer resets to
zero, and RESET goes low. The internal timer starts
after V
CC
returns above the reset threshold, and RESET
remains low for the reset timeout period.
The manual reset input (MR) can also initiate a reset.
See the Manual Reset Inputsection.
The MAX812 has an active-high RESET output that is
the inverse of the MAX811’s RESET output.
Manual Reset Input
Many μP-based products require manual reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic low on MR
asserts reset. Reset remains asserted while MR is low,
and for the Reset Active Timeout Period (t
RP
) after MR
returns high. This input has an internal 20k
pull-up
resistor, so it can be left open if it is not used. MR can
be driven with TTL or CMOS-logic levels, or with open-
drain/collector outputs. Connect a normally open
momentary switch from MR to GND to create a manual-
reset function; external debounce circuitry is not
required. If MR is driven from long cables or if the
device is used in a noisy environment, connecting a
0.1μF capacitor from MR to ground provides additional
noise immunity.
Reset T hreshold Ac c urac y
The MAX811/MAX812 are ideal for systems using a 5V
±5% or 3V ±5% power supply with ICs specified for 5V
±10% or 3V ±10%, respectively. They are designed to
meet worst-case specifications over temperature. The
reset is guaranteed to assert after the power supply
falls out of regulation, but before power drops below
the minimum specified operating voltage range for the
system ICs. The thresholds are pre-trimmed and exhibit
tight distribution, reducing the range over which an
undesirable reset may occur.
Manual Reset Input. A logic low on MR asserts reset. Reset remains asserted as long as MR is
low and for TBDms after MR returns high. This active-low input has an internal 20k
pull-up
resistor. It can be driven from a TTL or CMOS-logic line, or shorted to ground with a switch.
Leave open if unused.
3
3
+5V, +3.3V, or +3V Supply Voltage
4
4
Active-High Reset Output. RESET remains high while V
CC
is below the reset threshold or while
MR is held low. RESET remains high for Reset Active Timeout Period (t
RP
) after the reset condi-
tions are terminated.
2
—
Active-Low Reset Output. RESET remains low while V
CC
is below the reset threshold or while
MR is held low. RESET remains low for the Reset Active Timeout Period (t
RP
) after the reset
conditions are terminated.
—
2
Ground
1
1
FUNCTION
PIN
MR
V
CC
RESET
RESET
GND
NAME
MAX811
MAX812
相關PDF資料 |
PDF描述 |
|---|---|
| MAX814 | Accuracy, Low-Power, +3V and +5V μp Supervisory Circuits(高精度，±1%，低功耗，3V和5VμP監控電路) |
| MAX818 | Microprocessor Supervisory Circuits(5VμP監控電路,斷電警告) |
| MAX819 | Microprocessor Supervisory Circuits(5VμP監控電路,斷電警告) |
| MAX820 | Microprocessor and Non-Volatile Memory Supervisory Circuits |
| MAX820_CPE | Microprocessor and Non-Volatile Memory Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX812_EUS-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:4-Pin μP Voltage Monitors with Manual Reset Input |
| MAX81211ESA | 制造商:Maxim Integrated Products 功能描述:LOW COST, MICROPROCESSOR SUPERVISORY CIRCUIT - Bulk |
| MAX812CUS-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Analog IC |
| MAX812LCUS-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Voltage Detector |
| MAX812LEUS | 制造商:Maxim Integrated Products 功能描述:4-PIN UP VOLTAGE MONITORS WITH MANU - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。