- 您現在的位置：買賣IC網 > PDF目錄385551 > MAX812_EUS-T (Maxim Integrated Products, Inc.) 4-Pin レP Voltage Monitors with Manual Reset Input PDF資料下載
參數資料
| 型號： | MAX812_EUS-T |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 4-Pin レP Voltage Monitors with Manual Reset Input |
| 中文描述： | 4引腳レP的電壓監視器，帶有手動復位輸入 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 118K |
| 代理商： | MAX812_EUS-T |
M
__________ Applications Information
Negative-Going V
CC
Transients
In addition to issuing a reset to the μP during power-up,
power-down, and brownout conditions, the MAX811/
MAX812 are relatively immune to short duration nega-
tive-going V
CC
transients (glitches).
Figure 1 shows typical transient durations vs. reset
comparator overdrive, for which the MAX811/MAX812
do not generate a reset pulse. This graph was generat-
ed using a negative-going pulse applied to V
CC
, start-
ing above the actual reset threshold and ending below
it by the magnitude indicated (reset comparator over-
drive). The graph indicates the typical maximum pulse
width a negative-going V
CC
transient may have without
causing a reset pulse to be issued. As the magnitude
of the transient increases (goes farther below the reset
threshold), the maximum allowable pulse width
decreases. Typically, a V
CC
transient that goes 125mV
below the reset threshold and lasts 40μs or less
(MAX81_L/M) or 20μs or less (MAX81_T/S/R) will not
cause a reset pulse to be issued. A 0.1μF capacitor
mounted as close as possible to V
CC
provides addi-
tional transient immunity.
Ensuring a Valid RESET Output
Down to V
CC
= 0V
When V
CC
falls below 1V, the MAX811
RESET
output
no longer sinks current—it becomes an open circuit.
Therefore, high-impedance CMOS-logic inputs con-
nected to the
RESET
output can drift to undetermined
voltages. This presents no problem in most applica-
tions, since most μP and other circuitry is inoperative
with V
CC
below 1V. However, in applications where the
RESET
output must be valid down to 0V, adding a pull-
down resistor to the
RESET
pin will cause any stray
leakage currents to flow to ground, holding
RESET
low
(Figure 2). R1’s value is not critical; 100k
is large
enough not to load
RESET
and small enough to pull
RESET
to ground.
A 100k
pull-up resistor to V
CC
is also recommended
for the MAX812 if RESET is required to remain valid for
V
CC
< 1V.
4-Pin μP Voltage Monitors
with Manual Reset Input
6
_______________________________________________________________________________________
5
6
7
8
4
0
1
100
1000
2
1
3
RESET COMPARATOR OVERDRIVE , V
TH
- V
CC
(mV)
M
10
T
A
= +25
°
C
MAX81 _L/M
MAX81 _R/S/T
R1
V
CC
GND
MAX811
RESET
Figure 1. Maximum Transient Duration without Causing a
Reset Pulse vs. Comparator Overdrive
Figure 2. RESET Valid to V
CC
= Ground Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX812 | 4-Pin μp Voltage Monitors with Manual Reset Input(4管腳μP電壓監控器,低有效復位輸出) |
| MAX814 | Accuracy, Low-Power, +3V and +5V μp Supervisory Circuits(高精度，±1%，低功耗，3V和5VμP監控電路) |
| MAX818 | Microprocessor Supervisory Circuits(5VμP監控電路,斷電警告) |
| MAX819 | Microprocessor Supervisory Circuits(5VμP監控電路,斷電警告) |
| MAX820 | Microprocessor and Non-Volatile Memory Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX812LCUS-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Voltage Detector |
| MAX812LEUS | 制造商:Maxim Integrated Products 功能描述:4-PIN UP VOLTAGE MONITORS WITH MANU - Rail/Tube |
| MAX812LEUS | 制造商:Maxim Integrated Products 功能描述: |
| MAX812LEUS+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.63V 6UA 4PIN SOT-143 - Rail/Tube |
| MAX812LEUS+T | 功能描述:監控電路 4-Pin uPower Voltage Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。