- 您現在的位置：買賣IC網 > PDF目錄385551 > MAX799ESE (MAXIM INTEGRATED PRODUCTS INC) Octal D-type Edge-Triggered Flip-Flops with 3-State Outputs 20-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX799ESE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Octal D-type Edge-Triggered Flip-Flops with 3-State Outputs 20-CDIP -55 to 125 |
| 中文描述： | SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 15/32頁 |
| 文件大?。?/td> | 319K |
| 代理商： | MAX799ESE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
S tep-Down Controllers with
S ync hronous Rec tifier for CPU Power
______________________________________________________________________________________
15
The output filter capacitor C2 sets a dominant pole in
the feedback loop. This pole must roll off the loop gain
to unity before the zero introduced by the output
capacitor’s parasitic resistance (ESR) is encountered
(see Design Procedure section). A 60kHz pole-zero
cancellation filter provides additional rolloff above the
unity-gain crossover. This internal 60kHz lowpass com-
pensation filter cancels the zero due to the filter capaci-
tor’s ESR. The 60kHz filter is included in the loop in
both fixed- and adjustable-output modes.
S ync hronous-Rec tifier Driver (DL Pin)
Synchronous rectification reduces conduction losses in
the rectifier by shunting the normal Schottky diode with
a low-resistance MOSFET switch. The synchronous rec-
tifier also ensures proper start-up of the boost-gate driv-
er circuit. If you must omit the synchronous power
MOSFET for cost or other reasons, replace it with a
small-signal MOSFET such as a 2N7002.
If the circuit is operating in continuous-conduction
mode, the DL drive waveform is simply the complement
of the DH high-side drive waveform (with controlled
dead time to prevent cross-conduction or “shoot-
through”). In discontinuous (light-load) mode, the syn-
chronous switch is turned off as the inductor current
falls through zero. The synchronous rectifier works
under all operating conditions, including idle mode.
The synchronous-switch timing is further controlled by
the secondary feedback (SECFB) signal in order to
improve multiple-output cross-regulation (see
Secondary Feedback-Regulation Loop section).
Internal V L and REF S upplies
An internal regulator produces the 5V supply (VL) that
powers the PWM controller, logic, reference, and other
blocks within the MAX796. This +5V low-dropout linear
regulator can supply up to 5mA for external loads, with
a reserve of 20mA for gate-drive power. Bypass VL to
GND with 4.7μF.
Important
: VL must not be allowed to
exceed 6V. Measure VL with the main output fully
loaded. If VL is being pumped up above 5.5V, the
probable cause is either excessive boost-diode capaci-
tance or excessive ripple at V+. Use only small-signal
diodes for D2 (1N4148 preferred) and bypass V+ to
PGND with 0.1μF directly at the package pins.
The 2.505V reference (REF) is accurate to ±1.6% over
temperature, making REF useful as a precision system
reference. Bypass REF to GND with 0.33μF minimum.
REF can supply up to 1mA for external loads. However,
if tight-accuracy specs for either VOUT or REF are
essential, avoid loading REF with more than 100μA.
Loading REF reduces the main output voltage slightly,
according to the reference-voltage load regulation
error. In MAX799 applications, ensure that the SECFB
divider doesn’t load REF heavily.
When the main output voltage is above 4.5V, an internal P-
channel MOSFET switch connects CSL to VL while simul-
taneously shutting down the VL linear regulator. This
action bootstraps the IC, powering the internal circuitry
from the output voltage, rather than through a linear regu-
lator from the battery. Bootstrapping reduces power dissi-
pation caused by gate-charge and quiescent losses by
providing that power from a 90%-efficient switch-mode
source, rather than from a 50%-efficient linear regulator.
FB
REF
CSH
CSL
SLOPE COMPENSATION
VL
I1
R1
R2
TO PWM
LOGIC
OUTPUT DRIVER
UNCOMPENSATED
HIGH-SPEED
LEVEL TRANSLATOR
AND BUFFER
I2
I3
Figure 4. Main PWM Comparator Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX797HESE | High-Voltage, Step-Down Controller with Synchronous Rectifier for CPU Power |
| MAX799MJE | Step-Down Controllers with Synchronous Rectifier for CPU Power |
| MAX802 | 3.0V/3.3V Microprocessor Supervisory Circuits(具有看門狗和支持備用電池,高精度復位器) |
| MAX805 | 3.0V/3.3V Microprocessor Supervisory Circuits(具有看門狗和支持備用電池的復位器(高電壓復位)) |
| MAX704 | 3.0V/3.3V Microprocessor Supervisory Circuits(支持備用電池復位器,復位門限4.40V) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX799ESE+ | 制造商:Maxim Integrated Products 功能描述:CONV DC-DC SGL-OUT STEP DOWN 16SOIC N - Rail/Tube |
| MAX799ESE+T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX799ESE-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX799MJE | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX8 | 制造商:Lanzar 功能描述:4Ohm 600W Peak 8 Paper Cone Woofer 制造商:LANZAR 功能描述:8 PAPER CONE WOOFER 4OHM 600W PEAK |
發布緊急采購，3分鐘左右您將得到回復。