- 您現在的位置：買賣IC網 > PDF目錄385551 > MAX796EPE (MAXIM INTEGRATED PRODUCTS INC) Octal Bus Transceivers With 3-State Outputs 20-LCCC -55 to 125 PDF資料下載
參數資料
| 型號： | MAX796EPE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Octal Bus Transceivers With 3-State Outputs 20-LCCC -55 to 125 |
| 中文描述： | SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 319K |
| 代理商： | MAX796EPE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
S tep-Down Controllers with
S ync hronous Rec tifier for CPU Power
18
______________________________________________________________________________________
MAX796), a 1μs one-shot is triggered that extends the
low-side switch’s on-time beyond the point where the
inductor current crosses zero (in discontinuous mode).
This causes the inductor (primary) current to reverse,
which in turn pulls current out of the output filter capacitor
and causes the flyback transformer to operate in the for-
ward mode. The low impedance presented by the trans-
former secondary in the forward mode dumps current into
the secondary output, charging up the secondary capac-
itor and bringing SECFB back into regulation. The SECFB
feedback loop does not improve secondary output accu-
racy in normal flyback mode, where the main (primary)
output is heavily loaded. In this mode, secondary output
accuracy is determined, as usual, by the secondary recti-
fier drop, turns ratio, and accuracy of the main output
voltage. So, a linear post-regulator may still be needed in
order to meet tight output accuracy specifications.
The secondary output voltage-regulation point is deter-
mined by an external resistor divider at SECFB. For nega-
tive output voltages, the SECFB comparator is referenced
to GND (MAX799); for positive output voltages, SECFB
regulates at the 2.505V reference (MAX796). As a result,
output resistor divider connections and design equations
for the two device types differ slightly (Figure 9).
Ordinarily, the secondary regulation point is set 5% to
10% below the voltage normally produced by the flyback
effect. For example, if the output voltage as determined
by the turns ratio is +15V, the feedback resistor ratio
should be set to produce about +13.5V; otherwise, the
SECFB one-shot might be triggered unintentionally, caus-
ing an unnecessary increase in supply current and output
noise. In negative-output (MAX799) applications, the
resistor divider acts as a load on the internal reference,
which in turn can cause errors at the main output. Avoid
overloading REF (see the Reference Load-Regulation
Error vs. Load Current graph in the Typical Operating
Characteristics). 100k
is a good value for R3 in MAX799
circuits.
S oft-S tart Circ uit (S S )
Soft-start allows a gradual increase of the internal cur-
rent-limit level at start-up for the purpose of reducing
input surge currents, and perhaps for power-supply
sequencing. In shutdown mode, the soft-start circuit
holds the SS capacitor discharged to ground. When
SHDN goes high, a 4μA current source charges the SS
capacitor up to 3.2V. The resulting linear ramp wave-
form causes the internal current-limit level to increase
proportionally from 20mV to 100mV. The main output
capacitor thus charges up relatively slowly, depending
on the SS capacitor value. The exact time of the output
rise depends on output capacitance and load current
and is typically 1ms per nanofarad of soft-start capaci-
tance. With no SS capacitor connected, maximum cur-
rent limit is reached within 10μs.
S hutdown
Shutdown mode (
SHDN
= 0V) reduces the V+ supply
current to typically 1μA. In this mode, the reference and
VL are inactive.
SHDN
is a logic-level input, but it can
be safely driven to the full V+ range. Connect
SHDN
to
V+ for automatic start-up. Do not allow slow transitions
(slower than 0.02V/μs) on
SHDN
.
MAX796
MAX797
MAX799
MAX874
CSL
CSH
GND
FB
R5
VREF2 >>VREF
(4.096V)
R4
MAIN
OUTPUT
DH
DL
V
OUT
= V
REF
- (V
REF2
- V
REF
)(R5
V+
Figure 7. Output Voltage Less than 2.5V
MAX796
MAX797
MAX799
CSL
CSH
0.01
μ
F
0.01
μ
F
GND
FB
OUTPUT
(8V AS
SHOWN)
DH
DL
V
OUT
R
SENSE
DIVIDER IMPEDANCE
≤
5k
(EACH LEG)
= V
REF
(1 + R4
V+
R1
2.43k
R2
1.1k
R3
2.43k
R4
1.1k
Figure 8. Adjusting the Output Voltage to Greater than 6V
相關PDF資料 |
PDF描述 |
|---|---|
| MAX796ESE | Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX796MJE | Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX797CSE | Octal Bus Transceivers With 3-State Outputs 20-CFP -55 to 125 |
| MAX797EPE | Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX797ESE | Octal Bus Transceivers With 3-State Outputs 20-CFP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX796ESE | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX796ESE+ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX796ESE+T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX796ESE-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX796EVKIT-SO | 功能描述:電源管理IC開發工具 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。