- 您現在的位置：買賣IC網 > PDF目錄385549 > MAX756 (Maxim Integrated Products, Inc.) 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters(可調,高效率,步升DC-DC變換器) PDF資料下載
參數資料
| 型號： | MAX756 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | DC/DC變換器 |
| 英文描述： | 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters(可調,高效率,步升DC-DC變換器) |
| 中文描述： | 3.3V/5V/可調輸出、升壓型DC-DC轉換器 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 129K |
| 代理商： | MAX756 |
M
3.3V /5V /Adjustable-Output,
S tep-Up DC-DC Converters
_______________________________________________________________________________________
5
_______________Detailed Desc ription
Operating Princ iple
The MAX756/MAX757 combine a switch-mode regulator
with an N-channel MOSFET, precision voltage reference,
and power-fail detector in a single monolithic device.
The MOSFET is a “sense-FET” type for best efficiency,
and has a very low gate threshold voltage to ensure
start-up under low-battery voltage conditions (1.1V typ).
Pulse-Frequenc y
Modulation Control S c heme
A unique minimum off time, current-limited, pulse-frequen-
cy modulation (PFM) control scheme is a key feature of
the MAX756/MAX757. This PFM scheme combines the
advantages of pulse-width modulation (PWM) (high output
power and efficiency) with those of a traditional PFM
pulse-skipper (ultra-low quiescent currents). There is no
oscillator; at heavy loads, switching is accomplished
through a constant peak-current limit in the switch, which
allows the inductor current to self-oscillate between this
peak limit and some lesser value. At light loads, switching
frequency is governed by a pair of one-shots, which set a
minimum off-time (1μs) and a maximum on-time (4μs).
The switching frequency depends on the load and the
input voltage, and can range as high as 500kHz.
The peak switch current of the internal MOSFET power
switch is fixed at 1A ±0.2A. The switch's on resistance
is typically 0.5
, resulting in a switch voltage drop
(V
SW
) of about 500mV under high output loads. The
value of V
SW
decreases with light current loads.
Conventional PWM converters generate constant-fre-
quency switching noise, whereas this architecture pro-
duces variable-frequency switching noise. However,
the noise does not exceed the switch current limit times
the filter-capacitor equivalent series resistance (ESR),
unlike conventional pulse-skippers.
V oltage Referenc e
The precision voltage reference is suitable for driving
external loads such as an analog-to-digital converter.
It has guaranteed 250μA source-current and 20μA
sink-current capability. The reference is kept alive
even in shutdown mode. If the reference drives an
external load, bypass it with 0.22μF to GND. If the ref-
erence is unloaded, bypass it with at least 0.1μF.
Control-Logic Inputs
The control inputs (3/5, SHDN) are high-impedance
MOS gates protected against ESD damage by normally
reverse-biased clamp diodes. If these inputs are dri-
ven from signal sources that exceed the main supply
voltage, the diode current should be limited by a series
resistor (1M
suggested). The logic input threshold
level is the same (approximately 1V) in both 3.3V and
5V modes. Do not leave the control inputs floating.
__________________Design Proc edure
Output V oltage S elec tion
The MAX756 output voltage can be selected to 3.3V or
5V under logic control, or it can be left in one mode or
the other by tying 3/5 to GND or OUT. Efficiency varies
depending upon the battery and the load, and is typi-
cally better than 80% over a 2mA to 200mA load range.
The device is internally bootstrapped, with power
derived from the output voltage (via OUT). When the
output is set at 5V instead of 3.3V, the higher internal
supply voltage results in lower switch-transistor on
resistance and slightly greater output power.
Bootstrapping allows the battery voltage to sag to less
than 1V once the system is started. Therefore, the bat-
tery voltage range is from V
OUT
+ V
D
to less than 1V
(where V
D
is the forward drop of the Schottky rectifier).
If the battery voltage exceeds the programmed output
voltage, the output will follow the battery voltage. In
many systems this is acceptable; however, the output
voltage must not be forced above 7V.
The output voltage of the MAX757 is set by two resis-
tors, R1 and R2 (Figure 1), which form a voltage divider
between the output and the FB pin. The output voltage
is set by the equation:
V
OUT
= (V
REF
) [(R2 + R1) / R2]
where V
REF
= 1.25V.
To simplify resistor selection:
R1 = (R2) [(V
OUT
/ V
REF
) - 1]
Since the input bias current at FB has a maximum
value of 100nA, large values (10k
to 200k
) can be
used for R1 and R2 with no significant loss of accuracy.
For 1% error, the current through R1 should be at least
100 times FB’s bias current.
Low-Battery Detec tion
The MAX756/MAX757 contain on-chip circuitry for low-
battery detection. If the voltage at LBI falls below the reg-
ulator’s internal reference voltage (1.25V), LBO (an open-
drain output) sinks current to GND. The low-battery mon-
itor's threshold is set by two resistors, R3 and R4 (Figure
1), which forms a voltage divider between the input volt-
age and the LBI pin. The threshold voltage is set by R3
and R4 using the following equation:
R3 = [(V
IN
/ V
REF
) - 1] (R4)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX757 | 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters(可調,高效率,步升DC-DC變換器) |
| MAX7572 | Complete High Speed CMOS 12Bits ADC(單通道，3μs,帶基準源12位ADC) |
| MAX162 | CMOS 12Bits ADC(單通道，5μs,帶基準源12位ADC) |
| MAX7581 | CMOS 8Bits 8 Channel DAS(CMOS 8 位8通道數據采集系統) |
| MAX161 | CMOS 8Bits 8 Channel DAS(CMOS 8 位8通道數據采集系統) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX756C/D | 功能描述:直流/直流開關轉換器 Adjustable Output Step-Up DC-DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX756CPA | 功能描述:直流/直流開關轉換器 3.3/5/AdjV-Out Step Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX756CPA+ | 功能描述:直流/直流開關轉換器 3.3/5/AdjV-Out Step Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX756CSA | 功能描述:直流/直流開關轉換器 3.3/5/AdjV-Out Step Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX756CSA+ | 功能描述:直流/直流開關轉換器 3.3/5/AdjV-Out Step Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。