參數資料
型號： MAX6876ETX+T
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 電源管理
英文描述： EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit
中文描述： 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC36
封裝： 6 X 6 MM, 0.80 MM HEIGHT, MO-220WJJD-1, TQFN-36
文件頁數： 19/39頁
文件大?。?/td> 425K
代理商： MAX6876ETX+T
MAX6876
EEPROM-Programmable, Quad,
Power-Supply Tracker/Sequencer Circuit
26
______________________________________________________________________________________
REGISTERS
DESCRIPTIONS
Input Undervoltage Thresholds
(Registers 00h to 03h)
Input undervoltage thresholds (0.5V to 3.04V in 10mV increments or 1.0V to 5.5V in 20mV
increments). Each channel’s range is selected with register 08h.
Input Overvoltage Thresholds
(Registers 04h to 07h)
Input overvoltage thresholds (0.5V to 3.04V in 10mV increments or 1.0V to 5.5V in 20mV
increments). Each channel’s range is selected with register 08h.
Tracking/Sequencing Modes
Selects if outputs are to be sequenced or tracked. Sequencing/tracking modes are defined
by 4 bits for each OUT voltage of register 0Bh and 0Ch (see the Track/Sequence section).
Tracking/Sequencing
Power-Up/Down Slew Rate
Selectable output slew rate for power-up/down mode. Selected slew is overwritten during
tracking faults. Power-up/down slew rate is selected by bit [6:7] of register 12h.
Power-Up Delay Period
Power-up sequencing delay. Selects delay time for sequencing each supply.
Programmable delays are selected with bit [5:7] of register 0Fh.
Power-Down Sequence/Track
Behavior
Selectable power-down operation. Chooses if output voltages should be brought down in
the reverse sequence from power-up mode selections or if power supplies should be
simultaneously fast powered down (selected with bit 7 register 13h).
OUT Pulldown Enable
Selects if OUT_ should be internally pulled to GND when in fast shutdown or tracking fault
mode (selected with bit [6:3] register 13h).
Single/Multiple Device Application
Selects if the device will be used alone or in a master/slave application. If a single
application, the device can be operated in mixed sequencing/tracking modes. If multi-
device application, the device can be operated in tracking mode only (selected with bit
[7:6] register 09h).
00: single device 11: master device 01 or 10: slave device
Overcurrent Threshold
Selects IN_-to-OUT_ threshold voltage for overcurrent monitoring for each channel (register 0Dh).
Power-Good Threshold
Selects IN_-to-OUT_ threshold voltage for power-good monitoring for each channel
(register 10h).
Overcurrent Assert Select
Selects which overcurrent monitors will assert the OC output (selected by bit [5:2] of reg. 0Eh).
Overcurrent Filter Period
Selects the filter time for the overcurrent monitors. OC will not assert until the overcurrent
condition has existed longer than the selected filter period (selected by bit [7:6] of reg. 0Eh).
Fault Timeout Period
Selects the timeout period for sequencing/tracking completion. If sequencing/tracking
operation is not complete before the fault timeout period, a FAULT alert will be signaled
and all supplies will be powered down (selected by bit [7:4] of reg. 0Ah).
Fault Behavior
Selects how the device should operate during faults. Options include latch-off after fault or
autoretry after fault. Autoretry delay is selectable (selected by bit 5 of reg. 09h).
Reset Assert Select
Selects which OUT detectors will assert the RESET output (selected by bit [7:4] of reg. 11h).
Reset Timeout Period Select
Selects the reset timeout period (selected by bit [3:1] of reg. 11h).
Enable the Part with I
2C Interface
Bit 0 and bit 1 of register 09h allows a micro to turn the MAX6876 on/off with the I
2C
interface. While 09h[1] is 0, the part will ignore any enable command from I
2C. If 09h[1] is
set to 1, then 09h[0] has to be 1 to enable the part to power on.
Table 14. Registers Summary
相關PDF資料
PDF描述
MAX687CSA+T High-Accuracy, Low-Dropout Linear Regulators
MAX6880ETG+T Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors
MAX6881ETE+T Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors
MAX6882ETE+T Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors
MAX6883ETE+T Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors
相關代理商/技術參數
參數描述
MAX6876EVCMOD2 功能描述:監控電路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6876EVKIT 功能描述:監控電路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6877ETG 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6877ETG+ 功能描述:監控電路 Triple Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6877ETG+T 功能描述:監控電路 Triple Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*