- 您現在的位置：買賣IC網 > PDF目錄224188 > MAX6875ETJ+ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors PDF資料下載
參數資料
| 型號： | MAX6875ETJ+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors |
| 中文描述： | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC32 |
| 封裝： | 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-32 |
| 文件頁數： | 18/40頁 |
| 文件大?。?/td> | 337K |
| 代理商： | MAX6875ETJ+ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
MAX6874/MAX6875
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
______________________________________________________________________________________
25
A master device communicates to the MAX6874/
MAX6875 by transmitting the proper address followed by
command and/or data words. Each transmit sequence is
framed by a START (S) or REPEATED START (SR) condi-
tion and a STOP (P) condition. Each word transmitted
over the bus is 8 bits long and is always followed by an
acknowledge pulse.
SCL is a logic input, while SDA is a logic input/open-
drain output. SCL and SDA both require external pullup
resistors to generate the logic-high voltage. Use 4.7k
for most applications.
Bit Transfer
Each clock pulse transfers one data bit. The data on
SDA must remain stable while SCL is high (Figure 3),
otherwise the MAX6874/MAX6875 register a START or
STOP condition (Figure 4) from the master. SDA and
SCL idle high when the bus is not busy.
Start and Stop Conditions
Both SCL and SDA idle high when the bus is not busy. A
master device signals the beginning of a transmission
with a START (S) condition (Figure 4) by transitioning
SDA from high to low while SCL is high. The master
device issues a STOP (P) condition (Figure 4) by transi-
tioning SDA from low to high while SCL is high. A STOP
condition frees the bus for another transmission. The bus
remains active if a REPEATED START condition is gener-
ated, such as in the block read protocol (see Figure 7).
Early STOP Conditions
The MAX6874/MAX6875 recognize a STOP condition at
any point during transmission except if a STOP condition
occurs in the same high pulse as a START condition. This
condition is not a legal I2C format. At least one clock
pulse must separate any START and STOP condition.
STOP
CONDITION
REPEATED START
CONDITION
START
CONDITION
tHIGH
tLOW
tR
tF
tSU:DAT
tSU:STA
tSU:STO
tHD:STA
tBUF
tHD:STA
tHD:DAT
SCL
SDA
START
CONDITION
Figure 2. Serial-Interface Timing Details
DATA LINE STABLE,
DATA VALID
SDA
SCL
CHANGE OF
DATA ALLOWED
P
S
START
CONDITION
SDA
SCL
STOP
CONDITION
Figure 3. Bit Transfer
Figure 4. Start and Stop Conditions
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6876ETX+ | EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit |
| MAX6876ETX+T | EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit |
| MAX687CSA+T | High-Accuracy, Low-Dropout Linear Regulators |
| MAX6880ETG+T | Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors |
| MAX6881ETE+T | Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6875ETJ+ | 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6875ETJ+T | 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6875ETJ-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6876ETX | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6876ETX+ | 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。