參數資料
型號: MAX6874ETJ+T
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 電源管理
英文描述: EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors
中文描述: 6-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC32
封裝: 7 X 7 MM, TQFN-32
文件頁數: 20/40頁
文件大小: 403K
代理商: MAX6874ETJ+T
MAX6874/MAX6875
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
______________________________________________________________________________________
27
Send Byte
The send byte protocol allows the master device to send
one byte of data to the slave device (see Figure 7). The
send byte presets a register pointer address for a sub-
sequent read or write. The slave sends a NACK instead
of an ACK if the master tries to send an address that is
not allowed. If the master sends 80h, 81h, or 82h, the
data is ACK. This could be start of the write byte/word
protocol, and the slave expects at least one further
data byte. If the master sends a stop condition, the
internal address pointer does not change. If the master
sends 84h, this signifies that the block read protocol is
expected, and a repeated start condition should follow.
The device reboots if the master sends 88h. The send
byte procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends an 8-bit data byte.
5) The addressed slave asserts an ACK on SDA.
6) The master sends a stop condition.
Write Byte/Word
The write byte/word protocol allows the master device
to write a single byte in the register bank, preset an
EEPROM (configuration or user) address for a subse-
quent read, or to write a single byte to the configuration
or user EEPROM (see Figure 7). The write byte/word
procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends an 8-bit command code.
5) The addressed slave asserts an ACK on SDA.
6) The master sends an 8-bit data byte.
7) The addressed slave asserts an ACK on SDA.
8) The master sends a stop condition or sends another
8-bit data byte.
9) The addressed slave asserts an ACK on SDA.
10) The master sends a stop condition.
To write a single byte to the register bank, only the 8-bit
command code and a single 8-bit data byte are sent.
The command code must be in the range of 00h to 45h.
The data byte is written to the register bank if the com-
mand code is valid. The slave generates a NACK at
step 5 if the command code is invalid.
To preset an EEPROM (configuration or user) address
for a subsequent read, the 8-bit command code and a
single 8-bit data byte are sent. The command code
must be 80h if the write is to be directed into the config-
uration EEPROM, or 81h or 82h, if the write is to be
directed into the user EEPROM. If the command code is
80h, the data byte must be in the range of 00h to 45h. If
the command code is 81h or 82h, the data byte can be
00h to FFh. A NACK is generated in step 7 if none of the
above conditions are true.
To write a single byte of data to the user or configuration
EEPROM, the 8-bit command code and a single 8-bit
data byte are sent. The following 8-bit data byte is writ-
ten to the addressed EEPROM location.
SDA
SCL
1
MSB
LSB
START
01
0
A1
(0)
A0
XR/W
ACK
(MAX6875 ONLY)
Figure 6. Slave Address
相關PDF資料
PDF描述
MAX6875ETJ+T EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors
MAX6874ETJ+ EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors
MAX6875ETJ+ EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors
MAX6876ETX+ EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit
MAX6876ETX+T EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit
相關代理商/技術參數
參數描述
MAX6874TCC+ 制造商:Maxim Integrated Products 功能描述:
MAX6875ETJ 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6875ETJ+ 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6875ETJ+T 功能描述:監控電路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6875ETJ-T 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel