- 您現在的位置：買賣IC網 > PDF目錄383481 > MAX669 (Maxim Integrated Products, Inc.) QUADRUPLE 2-INPUT POSITIVE-OR GATES 14-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX669 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | QUADRUPLE 2-INPUT POSITIVE-OR GATES 14-CDIP -55 to 125 |
| 中文描述： | 1.8V至28V輸入、PWM升壓型控制器，µMAX封裝 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 326K |
| 代理商： | MAX669 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
Detailed Description
The MAX668/MAX669 current-mode PWM controllers
operate in a wide range of DC-DC conversion applica-
tions, including boost, SEPIC, flyback, and isolated out-
put configurations. Optimum conversion efficiency is
maintained over a wide range of loads by employing
both PWM operation and Maxim’s proprietary Idle
Mode control to minimize operating current at light
loads. Other features include shutdown, adjustable
internal operating frequency or synchronization to an
external clock, soft start, adjustable current limit, and a
wide (1.8V to 28V) input range.
MAX668 vs. MAX669 Differences
Differences between the MAX668 and MAX669 relate
to their use in bootstrapped or non-bootstrapped cir-
cuits (Table 1). The MAX668 operates with inputs as
low as 3V and can be connected in either a boot-
strapped or non-bootstrapped (IC powered from input
supply or other source) configuration. When not boot-
strapped, the MAX668 has no restriction on output volt-
age. When bootstrapped, the output cannot exceed
28V.
The MAX669 is optimized for low input voltages (down
to 1.8V) and requires bootstrapped operation (IC pow-
ered from V
OUT
) with output voltages no greater than
28V. Bootstrapping is required because the MAX669
does not have undervoltage lockout, but instead drives
EXT with an open-loop, 50% duty-cycle start-up oscilla-
tor when LDO is below 2.5V. It switches to closed-loop
operation only when LDO exceeds 2.5V. If a non-boot-
strapped connection is used with the MAX669 and if
V
CC
(the input voltage) remains below 2.7V, the output
voltage will soar above the regulation point. Table 2
recommends the appropriate device for each biasing
option.
M
1.8V to 28V Input, PWM Step-Up
Controllers in μMAX
8
_______________________________________________________________________________________
NAME
FUNCTION
1
LDO
5V On-Chip Regulator Output. This regulator powers all internal circuitry including the EXT gate driver.
Bypass LDO to GND with a 1μF or greater ceramic capacitor.
2
FREQ
Oscillator Frequency Set Input. A resistor from FREQ to GND sets the oscillator from 100kHz (R
OSC
=
500k
) to 500kHz (R
OSC
= 100k
). f
OSC
= 5 x 10
10
/ R
OSC
. R
OSC
is still required if an external clock is used
at SYNC/
SHDN
. (See SYNC/
SHDN
and FREQ Inputs section.)
PIN
3
4
GND
REF
Analog Ground
1.25V Reference Output. REF can source 50μA. Bypass to GND with a 0.22μF ceramic capacitor.
7
8
PGND
EXT
Power Ground for EXT Gate Driver and Negative Current-Sense Input
External MOSFET Gate-Driver Output. EXT swings from LDO to PGND.
6
CS+
Positive Current-Sense Input. Connect a current-sense resistor, R
CS
, between CS+ and PGND.
5
FB
Feedback Input. The FB threshold is 1.25V.
10
SYNC/
SHDN
Shutdown control and Synchronization Input. There are three operating modes:
SYNC/
SHDN
low: DC-DC off.
SYNC/
SHDN
high: DC-DC on with oscillator frequency set at FREQ by R
OSC
.
SYNC/
SHDN
clocked: DC-DC on with operating frequency set by SYNC clock input. DC-DC conversion
cycles initiate on rising edge of input clock.
9
V
CC
Input Supply to On-Chip LDO Regulator. V
CC
accepts inputs up to 28V. Bypass to GND with a 0.1μF ceramic
capacitor.
Pin Description
Table 1. MAX668/MAX669 Comparison
MAX668
MAX669
V
CC
Input
Range
3V to 28V
1.8V to 28V
Operation
Bootstrapped or nonboot-
strapped. V
CC
can be con-
nected to input, output, or
other voltage source such as
a logic supply.
Must be boot-
strapped (V
CC
must be connect-
ed to boosted out-
put voltage, V
OUT
).
Under-
voltage
Lockout
IC stops switching for LDO
below 2.5V.
No
Soft-Start
Yes
When LDO is
above 2.5V
FEATURE
相關PDF資料 |
PDF描述 |
|---|---|
| MAX668EUB | 1.8V to 28V Input, PWM Step-Up Controllers in レMAX |
| MAX6687AU75H | Local/Remote Temperature Switches in a レMAX Package |
| MAX6687AU40H | Local/Remote Temperature Switches in a レMAX Package |
| MAX6688AU40H | Local/Remote Temperature Switches in a レMAX Package |
| MAX6687AU40L | Local/Remote Temperature Switches in a レMAX Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX66901-K00# | 功能描述:射頻識別變換器工具 MAX66901 RF Eval Kit RoHS:否 制造商:Olimex Ltd. 產品:RFID Readers 用于:ISO15693 |
| MAX66902-K00# | 功能描述:射頻識別變換器工具 HF DEVELOPER KIT RoHS:否 制造商:Olimex Ltd. 產品:RFID Readers 用于:ISO15693 |
| MAX66903-K00 | 功能描述:射頻識別變換器工具 MAX6100/20/40 Eval Kit RoHS:否 制造商:Olimex Ltd. 產品:RFID Readers 用于:ISO15693 |
| MAX6690MEE | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6690MEE+ | 功能描述:板上安裝溫度傳感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。