- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6698UE99+ (Maxim Integrated)IC TEMP MONITOR 7CH 16-TSSOP Datasheet資料下載
參數資料
| 型號： | MAX6698UE99+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 321K |
| 描述： | IC TEMP MONITOR 7CH 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 96 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±3.5°C 本地（最大），±3°C 遠程（最大） |
| 拓撲： | ADC，緩沖器，多路復用器，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
ALERT Interrupt Mode
An ALERT interrupt occurs when the internal or external
temperature reading exceeds a high-temperature limit
(user programmable). The ALERT interrupt output sig-
nal can be cleared by reading the status register(s)
associated with the fault(s) or by successfully respond-
ing to an alert response address transmission by the
master. In both cases, the alert is cleared but is
reasserted at the end of the next conversion if the fault
condition still exists. The interrupt does not halt auto-
matic conversions. The ALERT output is open drain so
that multiple devices can share a common interrupt
line. All ALERT interrupts can be masked using the
configuration 3 register. The POR state of these regis-
ters is shown in Table 4.
ALERT Response Address
The SMBus alert response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex logic needed to be a bus master.
Upon receiving an interrupt signal, the host master can
broadcast a receive byte transmission to the alert
response slave address (see the Slave Addresses sec-
tion). Then, any slave device that generated an inter-
rupt attempts to identify itself by putting its own
address on the bus.
The alert response can activate several different slave
devices simultaneously, similar to the I
2
C General Call.
If more than one slave attempts to respond, bus arbitra-
tion rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledgment and continues to hold the ALERT line
low until cleared. (The conditions for clearing an alert
vary depending on the type of slave device.)
Successful completion of the alert response protocol
clears the output latch. If the condition that caused the
alert still exists, the MAX6698 reasserts the ALERT
interrupt at the end of the next conversion.
OVERT Overtemperature Alarms
The MAX6698 has four overtemperature registers that
store remote alarm threshold data for the OVERT out-
put. OVERT is asserted when a channels measured
temperature (voltage in the case of the thermistor chan-
nels) is greater than the value stored in the correspond-
ing threshold register. OVERT remains asserted until
the temperature drops below the programmed thresh-
old minus 4癈 hysteresis for remote-diode channel 1, or
4 LSB hysteresis for thermistor channels 1, 2, and 3. An
overtemperature output can be used to activate a cool-
ing fan, send a warning, initiate clock throttling, or trig-
ger a system shutdown to prevent component damage.
See Table 4 for the POR state of the overtemperature
threshold registers.
Command Byte Functions
The 8-bit command byte register (Table 4) is the master
index that points to the various other registers within the
MAX6698. This registers POR state is 0000 0000.
Configuration Bytes Functions
There are three read-write configuration registers
(Tables 5, 6, 7) that can be used to control the
MAX6698s operation.
Configuration 1 Register
The configuration 1 register (Table 5) has several func-
tions. Bit 7(MSB) is used to put the MAX6698 either in
software standby mode (STOP) or continuous conver-
sion mode. Bit 6 resets all registers to their power-on
reset conditions and then clears itself. Bit 5 disables
the SMBus timeout. Bit 4 enables more frequent con-
versions on channel 1, as described in the ADC
Conversion Sequence section. Bit 3 enables resistance
cancellation on channel 1. See the Series Resistance
Cancellation section for more details. The remaining
bits of the configuration 1 register are not used. The
POR state of this register is 0000 0000 (00h).
Configuration 2 Register
The configuration 2 register functions are described in
Table 6. Bits [6:0] are used to mask the ALERT interrupt
output. Bit 6 masks the local alert interrupt, bits 5
through 3 mask the remote-diode ALERT interrupts, and
bits 2 through 0 mask the thermistor alert interrupts. The
power-up state of this register is 0000 0000 (00h).
Configuration 3 Register
Table 7 describes the configuration 3 register. Bits 5, 4,
3, and 0 mask the OVERT interrupt output for thermistor
channels 1, 2, and 3 and remote-diode channel 1. The
remaining bits, 7, 6, 2, and 1, are reserved. The power-
up state of this register is 0000 0000 (00h).
7-Channel Precision Remote-Diode, Thermistor,
and Local Temperature Monitor
10 ______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6699EE34+ | IC TEMP MONITOR 5CH 16-QSOP |
| MAX7500MTA+T | IC TEMP SENSOR DGTL 8TDFN |
| MAX786CAI | IC REG QD BCK/LINEAR SYNC 28SSOP |
| MAX8533EUB+T | IC HOT-SWAP CNTRLR 12V 10-UMAX |
| MAX8563EEE+ | IC REG CTRLR TRPL POS ADJ 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6698UE99+ | 功能描述:板上安裝溫度傳感器 7Ch Precision Remote Diode Thermistor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6698UE99+T | 功能描述:板上安裝溫度傳感器 7Ch Precision Remote Diode Thermistor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6698UE99-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6698UE9C | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6698UE9C+ | 功能描述:板上安裝溫度傳感器 7Ch Precision Remote Diode Thermistor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。