- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6689UP34+ (Maxim Integrated)IC 7CH PREC TEMP MONITOR 20TSSOP Datasheet資料下載
參數資料
| 型號： | MAX6689UP34+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 12/19頁 |
| 文件大?。?/td> | 240K |
| 描述： | IC 7CH PREC TEMP MONITOR 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 74 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±1°C 本地（最大），±3°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC，緩沖器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
In both cases, the alert is cleared even if the fault condi-
tion exists, but the ALERT output reasserts at the end of
the next conversion. The bits indicating the fault for the
OVERT interrupt output clear only on reading the status 2
register even if the fault conditions still exist. Reading the
status 2 register does not clear the OVERT interrupt out-
put. To eliminate the fault condition, either the measured
temperature must drop below the temperature threshold
minus the hysteresis value (4癈), or the trip temperature
must be set at least 4癈 above the current temperature.
Applications Information
Remote-Diode Selection
The MAX6689 directly measures the die temperature of
CPUs and other ICs that have on-chip temperature-
sensing diodes (see the Typical Application Circuit) or
it can measure the temperature of a discrete diode-
connected transistor.
Effect of Ideality Factor
The accuracy of the remote temperature measure-
ments depends on the ideality factor (n) of the remote
diode (actually a transistor). The MAX6689 is opti-
mized for n = 1.012. A thermal diode on the substrate
of an IC is normally a pnp with the base and emitter
brought out the collector (diode connection) grounded.
DXP_ must be connected to the anode (emitter) and
DXN_ must be connected to the cathode (base) of this
pnp. If a sense transistor with an ideality factor other
than 1.012 is used, the output data is different from the
data obtained with the optimum ideality factor.
Fortunately, the difference is predictable. Assume a
remote-diode sensor designed for a nominal ideality
7-Channel Precision Temperature Monitor
12 ______________________________________________________________________________________
BIT
NAME
POR
STATE
FUNCTION
7 (MSB)
STOP
0
Standby-Mode Control Bit. If STOP is set to logic 1, the MAX6689 stops
converting and enters standby mode.
6
POR
0
Reset Bit. Set to logic 1 to put the device into its power-on state. This bit is self-
clearing.
5
TIMEOUT
0
Timeout Enable Bit. Set to logic 0 to enable SMBus timeout.
4
Fast remote 1
0
Channel 1 Fast-Conversion Bit. Set to logic 1 to enable fast conversion of
channel 1.
3
Resistance
cancellation
0
Resistance Cancellation Bit. When set to logic 1, the MAX6689 cancels series
resistance in the channel 1 thermal diode.
2
Reserved
0
1
Reserved
0
0
Reserved
0
Table 4. Configuration 1 Register
Table 5. Configuration 2 Register
BIT
NAME
POR
STATE
FUNCTION
7 (MSB)
Reserved
0
6
Mask Local ALERT
0
Local Alert Mask. Set to logic 1 to mask local channel ALERT.
5
Mask ALERT 6
0
Channel 6 Alert Mask. Set to logic 1 to mask channel 6 ALERT.
4
Mask ALERT 5
0
Channel 5 Alert Interrupt Mask. Set to logic 1 to mask channel 5 ALERT.
3
Mask ALERT 4
0
Channel 4 Alert Mask. Set to logic 1 to mask channel 4 ALERT.
2
Mask ALERT 3
0
Channel 3 Alert Interrupt Mask. Set to logic 1 to mask channel 3 ALERT.
1
Mask ALERT 2
0
Channel 2 Alert Mask. Set to logic 1 to mask channel 2 ALERT.
0
Mask ALERT 1
0
Channel 1 Alert Mask. Set to logic 1 to mask channel 1 ALERT.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6690MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6692YMSA+ | IC SENSOR REMOTE SMBUS 8SOIC |
| MAX6693UP9A+T | IC TEMP MONITOR 7CH 20-TSSOP |
| MAX6694TE9A+T | IC TEMP MONITOR 5CH 16TQFN |
| MAX6695YAUB+ | IC SENSOR TEMP SMBUS 10-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6689UP34+ | 功能描述:板上安裝溫度傳感器 7Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6689UP34+T | 功能描述:板上安裝溫度傳感器 7Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6689UP34-T | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Tape and Reel |
| MAX6689UP38 | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Rail/Tube |
| MAX6689UP38-T | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。