- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6652AUB+T (Maxim Integrated)IC TEMP SENS/MON 10-UMAX Datasheet資料下載
參數資料
| 型號： | MAX6652AUB+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 165K |
| 描述： | IC TEMP SENS/MON 10-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±2°C（最小值） |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-uMAX |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1425 (CN2011-ZH PDF) |
| 其它名稱： | MAX6652AUB+TDKR |
Low-Power Shutdown Mode
Setting bit 0 in the configuration register to 0 stops the
monitoring loop and puts the MAX6652 into low-power
shutdown mode. In this mode, the I
2
C-compatible/
SMBus interface remains active, and the supply current
drops to 10礎 or less.
Power-On Reset (POR)
The MAX6652 power-on reset supply (POR) voltage is
typically 2V. Below this supply voltage, all registers are
reset, the device is put into shutdown mode, and the
I
2
C-compatible/SMBus interface is inactive.
Alarm Threshold Registers
Two registers, a hot temperature limit (T
HOT
) at 39h and
a hot temperature hysteresis (T
HYST
) at 3Ah, store
alarm threshold data (Table 1). If a measured tempera-
ture exceeds the value of T
HOT
, an ALERT is asserted.
Alerts are cleared and reasserted depending on the
interrupt mode selected in the temperature configura-
tion register (see ALERT Interrupts).
The POR state of the T
HOT
register is 0101 0000 or
+80癈. The POR state of the T
HYST
register is 0100
0001 or +65癈.
High and low limits for the voltage inputs are stored in
registers 2Bh through 32h. If a measured voltage is
less than V
LOW
or greater than V
HIGH
, an ALERT is
asserted.
The POR states of the high- and low-voltage limits are
1.1 and 0.9 times the nominal voltage for each input,
respectively.
Interrupt Status Byte Functions
The interrupt status register records temperature or
voltage fault conditions whenever a limit is exceeded
(Table 5). Bits 0 through 3 correspond to the 2.5V, 12V,
3.3V, and 5V internal V
CC
voltage inputs, and bit 4 cor-
responds to the temperature. If a threshold has been
crossed, the appropriate bit will contain a 1. In the
default and one-time interrupt modes, reading the sta-
tus register clears the register until a new out-of-range
condition is detected.
ALERT Interrupts
An out-of-range voltage or temperature causes the
ALERT output signal to be asserted. However, if the
assertion is caused by an out-of-range temperature, the
ALERT output can operate in one of three different
modes: default, one-time interrupt, and comparator
modes. The ALERT signal can be cleared only by read-
ing the interrupt status register (Table 5), except when
the ALERT has been activated by an out-of-range tem-
perature in comparator mode. In this case, ALERT is
only cleared when the fault is removed. Reading the
interrupt status register also clears this register, except
for bit 4 in comparator mode. Unless the fault is
removed, ALERT will be reasserted after the next con-
version cycle. The ALERT output can also be masked
by writing to the appropriate bits in the interrupt mask
register (Table 6) or by setting bit 1 of the configuration
register (Table 4) to 0.
The interrupt does not halt conversions. New tempera-
ture and voltage data continue to be available over the
I
2
C-compatible/SMBus interface after ALERT is assert-
ed. The three temperature ALERT modes are illustrated
in Figure 1 and are selected through the temperature
configuration register (Table 7). The ALERT output pin
is open drain, so the device can share a common inter-
rupt line.
Temperature Sensor and System Monitor
in a 10-Pin 礛AX
8 _______________________________________________________________________________________
Table 6. Interrupt Mask Register (Address 43h, Power-Up Default = 00h)
BIT
NAME
READ/WRITE
DESCRIPTION
0
2.5V
R/W
Setting the bit to 1 disables the interrupt status register bit (bit 0) and the ALERT
output for the 2.5V
IN
input.
1
12V
R/W
Setting the bit to 1 disables the interrupt status register bit (bit 1) and the ALERT
output for the 12V
IN
input.
2
3.3V
R/W
Setting the bit to 1 disables the interrupt status register bit (bit 2) and the ALERT
output for the 3.3V
IN
input.
3
5.0V
R/W
Setting the bit to 1 disables the interrupt status register bit (bit 3) and the ALERT
output for the V
CC
input.
4
Tem p er atur e
R/W
Setting the bit to 1 disables the interrupt status register bit (bit 4) and the ALERT
output for temperature.
5, 6, 7
Reserved
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6659MEE+T | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6661AEE+T | IC REG FAN SPEED 16-QSOP |
| MAX6664AEE+T | IC TEMP MON FAN CNTRL 16-QSOP |
| MAX6665ASA45+ | IC FAN CNTRL/DRVR 8-SOIC |
| MAX6670AUB45+ | IC TEMP SENSOR REMOTE 10-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6652EUB | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6653AEE | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6653AEE+ | 功能描述:板上安裝溫度傳感器 Temperature Monitor & PWM Fan Controller RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6653AEE+T | 功能描述:板上安裝溫度傳感器 Temperature Monitor & PWM Fan Controller RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6653AEE-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。