- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX6622UE9A+T (Maxim Integrated)IC PREC TEMP MONITOR 5CH 16TSSOP Datasheet資料下載
參數資料
| 型號： | MAX6622UE9A+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 6/18頁 |
| 文件大小： | 196K |
| 描述： | IC PREC TEMP MONITOR 5CH 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 溫度監(jiān)控系統(tǒng)（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | -0.1°C 本地，±3°C 遠程 |
| 拓撲： | ADC，緩沖器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
Detailed Description
The MAX6622 is a precision multichannel temperature
monitor that features one local and four remote temper-
ature-sensing channels with a programmable alert
threshold for each temperature channel and a program-
mable overtemperature threshold for channels 1 and 4
(see Figure 1). Communication with the MAX6622 is
achieved through the SMBus serial interface and a
dedicated alert output. The alarm outputs, OVERT and
ALERT, assert if the software-programmed temperature
thresholds are exceeded. ALERT typically serves as an
interrupt, while OVERT can be connected to a fan, sys-
tem shutdown, or other thermal-management circuitry.
ADC Conversion Sequence
In the default conversion mode, the MAX6622 starts the
conversion sequence by measuring the temperature on
channel 1, followed by 2, 3, local channel, and 4. The
conversion result for each active channel is stored in
the corresponding temperature data register.
In some systems, one of the remote thermal diodes may
be monitoring a location that experiences temperature
changes that occur much more rapidly than in the other
channels. If faster temperature changes must be moni-
tored in one of the temperature channels, the MAX6622
allows channel 1 to be monitored at a faster rate than
the other channels. In this mode (set by writing a 1 to
bit 4 of the configuration 1 register), measurements of
channel 1 alternate with measurements of the other
channels. The sequence becomes channel 1, channel
2, channel 1, channel 3, channel 1, etc. Note that the
time required to measure all five channels is consider-
ably greater in this mode than in the default mode.
Low-Power Standby Mode
Enter software standby mode by setting the STOP bit to
1 in the configuration 1 register. Enter hardware standby
by pulling STBY low. Software standby mode disables
the ADC and reduces the supply current to approximate-
ly 30礎. Hardware standby mode halts the ADC clock,
but the supply current is approximately 350礎. During
either software or hardware standby, data is retained in
memory, and the SMBus interface is active and listening
for SMBus commands. The timeout is enabled if a
START condition is recognized on SMBus. Activity on the
SMBus causes the supply current to increase. If a stand-
by command is received while a conversion is in
progress, the conversion cycle is interrupted, and the
temperature registers are not updated. The previous
data is not changed and remains available.
5-Channel Precision Temperature Monitor
6 _______________________________________________________________________________________
PIN
NAME
FUNCTION
7
DXP4
Combined Current Source and A/D Positive Input for Channel 4 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave unconnected or connect to V
CC
if
no remote diode is used. Place a 2200pF capacitor between DXP4 and DXN4 for noise filtering.
8
DXN4
Cathode Input for Channel 4 Remote Diode. Connect the cathode of the channel 4 remote-diode-
connected transistor to DXN4.
9
STBY
Standby Input. Drive STBY logic-low to place the MAX6622 in hardware standby mode, or logic-high
for normal operation. Temperature and threshold data are retained in standby mode.
10
N.C.
No Connection. Must be connected to ground.
11
OVERT
Overtemperature Active-Low, Open-Drain Output. OVERT asserts low when the temperature of
channels 1 and 4 exceed the programmed threshold limit.
12
V
CC
Supply Voltage Input. Bypass to GND with a 0.1礔 capacitor.
13
ALERT
SMBus Alert (Interrupt), Active-Low, Open-Drain Output. ALERT asserts low when the temperature of
any channel exceeds the programmed ALERT threshold.
14
SMBDATA SMBus Serial-Data Input/Output. Connect to a pullup resistor.
15
SMBCLK
SMBus Serial-Clock Input. Connect to a pullup resistor.
16
GND
Ground
Pin Description (continued)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6626RMTT+T | IC TEMP SENSOR I2C 6-TDFN |
| MAX6627MKA#TG16 | IC TEMP SENSOR DGTL SOT23-8 |
| MAX6636UP9A+T | IC PREC TEMP MONITOR 7CH 20TSSOP |
| MAX6639FATE+ | IC 2CH TEMP MONITOR 16TQFN |
| MAX6641AUB92+ | IC TEMP MONITOR SMBUS 10UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX66240ETA+ | 制造商:Maxim Integrated Products 功能描述:HF 4KBIT SHA-256 SECURE EEPROM - Rail/Tube |
| MAX66240ETA+T | 制造商:Maxim Integrated Products 功能描述:HF 4KBIT SHA-256 SECURE EEPROM - Tape and Reel |
| MAX6625PMTT+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL I2C 6TDFN EP - Rail/Tube |
| MAX6625PMTT+T | 功能描述:板上安裝溫度傳感器 9-Bit/12-Bit Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6625PMUT | 制造商:Maxim Integrated Products 功能描述:9-BIT TEMPERATURE SENSOR W/ I2CC-COMPATIBLE S - Rail/Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。