參數資料
型號: MAX6519
廠商: Maxim Integrated Products, Inc.
元件分類: 溫度/濕度傳感器
英文描述: Low-Cost. 2.7V to 5.5V. Analog Temperature Sensor Switches in a SOT23
中文描述: 低成本、2.7V至5.5V、模擬溫度傳感器開關,SOT23封裝
文件頁數: 7/10頁
文件大小: 212K
代理商: MAX6519
Calculate the temperature using the formula:
Verify that the temperature measured is within ±2
°
C
of the ambient board temperature. Measure the
ambient board temperature using an accurate cali-
brated temperature sensor.
Connect OUT to ground (OUT to V
CC
for cold
threshold versions) and observe the state change of
the logic output.
Disconnect OUT from ground and observe that the
logic output reverts to its initial state.
Hysteresis Testing
The MAX6516
MAX6519 can be programmed with 2
°
C
or 10
°
C of hysteresis by pin strapping HYST to V
CC
or
GND, respectively. Below is a test feature that can be
used to measure the accuracy of the device
s hystere-
sis using a device with a +65
°
C threshold:
Power up the device and observe the state of the
digital output.
Drive the OUT voltage down gradually.
When the digital output changes state, note V
OUT
.
V
OUT
trip = V
OUT
at logic output change of state
(high to low or low to high).
Calculate trip temperature (T1) using:
Gradually raise V
OUT
until the digital output reverts to
its initial state and note V
OUT
.
Calculate trip temperature (T2).
T
HYST
= T2 - T1.
Thermal Considerations
The MAX6516
MAX6519 supply current is typically 22μA.
When used to drive high-impedance loads, the devices
dissipate negligible power. Therefore, the die tempera-
ture is essentially the same as the package temperature.
Accurate temperature monitoring depends on the thermal
resistance between the device being monitored and the
MAX6516
MAX6519 die. Heat flows in and out of plastic
packages, primarily through the leads. Pin 2 of the 5-pin
SOT23 package provides the lowest thermal resistance to
the die. Short, wide copper traces between the
MAX6516
MAX6519 and the object whose temperature
is being monitored ensures heat transfers occur quickly
and reliably. The rise in die temperature due to self-heat-
ing is given by the following formula:
T
J
= P
DISSIPATION
θ
JA
where P
DISSIPATION
is the power dissipated by the
MAX6516
MAX6519, and
θ
JA
is the thermal resistance
of the package.
The typical thermal resistance is +140
°
C/W for the
5-pin SOT23 package. To limit the effects of self-
heating, minimize the output current. For example, if the
MAX6516
MAX6519 sink 1mA, the open-drain output
voltage is guaranteed to be less than 0.3V. Therefore,
an additional 0.3mW of power is dissipated within the
IC. This corresponds to a 0.042
°
C shift in the die tem-
perature in the 5-pin SOT23 package.
Chip Information
TRANSISTOR COUNT: 1808
PROCESS: BiCMOS
T
V
OUT
=
+
1 8015
0 01062
.
30
.
T
V
OUT
=
+
1 8015
0 01062
.
30
.
M
Low-Cost, 2.7V to 5.5V, Analog Temperature
Sensor Switches in a SOT23
_______________________________________________________________________________________
7
相關PDF資料
PDF描述
MAX6516UK Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
MAX6517UK Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
MAX6518UK Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
MAX6519UK Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
MAX6516-MAX6519 8-Bit Shift Register 20-PDIP -40 to 125
相關代理商/技術參數
參數描述
MAX6519UKN005+ 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR ANLG 5PIN SOT-23 - Rail/Tube
MAX6519UKN005+T 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR ANLG 5PIN SOT-23 - Tape and Reel
MAX6519UKN015+ 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR ANLG 5PIN SOT-23 - Rail/Tube
MAX6519UKN015+T 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR ANLG 5PIN SOT-23 - Tape and Reel
MAX6519UKN025+ 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR ANLG 5PIN SOT-23 - Rail/Tube