- 您現在的位置：買賣IC網 > PDF目錄354346 > MAX6474TA21BD1 (MAXIM INTEGRATED PRODUCTS INC) 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit PDF資料下載
參數資料
| 型號： | MAX6474TA21BD1 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 中文描述： | FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, DSO8 |
| 封裝： | 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEC, TDFN-8 |
| 文件頁數： | 12/13頁 |
| 文件大?。?/td> | 261K |
| 代理商： | MAX6474TA21BD1 |
MAX6443–MAX6452
a microprocessor for general-purpose I/O control. MR2
monitors a switch to detect when a smart card is inserted.
When the switch is closed high (card inserted), RESET
one-shot pulses low for 140ms. MR2 is internally
debounced for 210ms to prevent false resets when the
smart card is removed.
Interfacing to Other Voltages
for Logic Compatibility
The open-drain RESET output can be used to interface
to a P with other logic levels. As shown in Figure 8, the
open-drain output can be connected to voltages from 0
to 6V.
Generally, the pullup resistor connected to the RESET
connects to the supply voltage that is being monitored
at the IC’s VCC pin. However, some systems may use
the open-drain output to level-shift from the monitored
supply to reset circuitry powered by some other supply
(Figure 8). Keep in mind that as the supervisor’s VCC
decreases toward 1V, so does the IC’s ability to sink
current at RESET. RESET is pulled high as VCC decays
toward 0. The voltage where this occurs depends on
the pullup resistor value and the voltage to which it is
connected.
Ensuring a Valid RESET Down to
VCC = 0V (Push-Pull RESET)
When VCC falls below 1V, RESET current-sinking capa-
bilities decline drastically. The high-impedance CMOS-
logic inputs connected to RESET can drift to
undetermined voltages. This presents no problems in
most applications, because most Ps and other circuitry
do not operate with VCC below 1V.
In applications in which RESET must be valid down to
0V, add a pulldown resistor between RESET and GND
for the push-pull outputs. The resistor sinks any stray
leakage currents, holding RESET low (Figure 9). The
value of the pulldown resistor is not critical; 100k
is
large enough not to load RESET and small enough to
pull RESET to ground. The external pulldown cannot be
used with the open-drain reset outputs.
Transient Immunity
In addition to issuing a reset to the P during power-up,
power-down, and brownout conditions, these supervi-
sors are relatively immune to short-duration falling tran-
sients (glitches). The graph Maximum Transient Duration
vs. Reset Threshold Overdrive in the Typical Operating
Characteristics section shows this relationship.
P Reset Circuits with Long Manual Reset
Setup Period
8
_______________________________________________________________________________________
MAX6451
P
VCC
RSTIN
RESET
DIGITAL INPUT
I/O SUPPLY
CORE SUPPLY
+3.3V
+1.5V
RESET
MR1
MR2
GND
FRONT-PANEL SWITCH
STANDARD
P INPUT
AND 6.72s MANUAL
RESET DELAY
SMART CARD DETECT:
IMMEDIATE ONE-SHOT
WHEN MANUAL
RESET CLOSES
Figure 7. MAX6451/MAX6452 Application Circuit
MAX6444
MAX6446
MAX6448
MAX6450
MAX6452
P
RESET
GND
VCC
5V
3.3V
100k
N
Figure 8. Interfacing to Other Voltage Levels
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6474TA21BD1-T | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| MAX6474TA21BD2 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| MAX6474TA21BD2-T | Digitally Controlled Potentiometer (XDCP™); Temperature Range: 0°C to 70°C; Package: 8-MSOP |
| MAX6474TA21BD3 | Digitally Controlled Potentiometer (XDCP™); Temperature Range: 0°C to 70°C; Package: 8-MSOP |
| MAX6474TA21BD3-T | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6474TA21BD1+T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX6474TA21BD1-T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX6474TA21BD2+T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX6474TA21BD2-T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX6474TA21BD3+T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。