- 您現在的位置：買賣IC網 > PDF目錄299461 > MAX6351MRUT-T (MAXIM INTEGRATED PRODUCTS INC) Dual/Triple-Voltage レP Supervisory Circuits PDF資料下載
參數資料
| 型號： | MAX6351MRUT-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Dual/Triple-Voltage レP Supervisory Circuits |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | SOT-23, 6 PIN |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 280K |
| 代理商： | MAX6351MRUT-T |
MAX6351–MAX6360
Dual/Triple-Voltage
P Supervisory Circuits
8
_______________________________________________________________________________________
During the normal operating mode, the supervisor will
issue a reset pulse for the reset timeout period (140ms
min) if the P does not update the WDI with a valid tran-
sition (HIGH to LOW or LOW to HIGH) within the stan-
dard timeout period (1.6s min).
After each reset event (VCC power-up, manual reset, or
watchdog reset), there is an initial watchdog startup
timeout period of 25.6s. The startup mode provides an
extended period for the system to power up and fully
initialize all P and system components before assum-
ing responsibility for routine watchdog updates. The
normal watchdog timeout period (1.6s min) begins at
the conclusion of the startup timeout period or after the
first transition on WDI before the conclusion of the start-
up period (Figure 3).
Applications Information
Ensuring a Valid RESET Output
Down to VCC = 0
In some systems, it is necessary to ensure a valid reset
even if VCC falls to 0. In these applications, use the cir-
cuit shown in Figure 4. Note that this configuration does
not work for the open-drain outputs of the MAX6352/
MAX6355/MAX6358.
Interfacing to Ps with
Bidirectional Reset Pins
Microprocessors with bidirectional reset pins will con-
tend with the push-pull outputs of these devices. To
prevent this, connect a 4.7k
resistor between RESET
and the P’s reset I/O port, as shown in Figure 5. Buffer
RESET as shown in the figure if this reset is used by
other components in the system.
Figure 4. Ensuring a Valid Reset Low to VCC1 and VCC2 = 0
VCC2VCC1
GND
100k
RST2
RST1
RST
MAX6351 MAX6356
MAX6353 MAX6357
MAX6354 MAX6359
MAX6360
VCC2
VCC1
Figure 5. Interfacing to Ps with Bidirectional Reset I/O
BUFFERED RESET TO OTHER SYSTEM COMPONENTS
4.7k
GND
RESET
P
GND
RST2
RST1
RST
MAX6351–MAX6360
VCC2
VCC1
1.6s
MAX
tWDI-NORMAL
1.6s MAX
tWDI-STARTUP
25.6s MAX
VTH
VCC
WDI
RESET
140ms
Figure 3. Normal Watchdog Startup Sequence
Chip Information
TRANSISTOR COUNT: 855
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6353LTUK-T | Dual/Triple-Voltage レP Supervisory Circuits |
| MAX6353MRUK-T | Dual/Triple-Voltage レP Supervisory Circuits |
| MAX6353MTUK-T | Dual/Triple-Voltage レP Supervisory Circuits |
| MAX6354LTUK-T | Dual/Triple-Voltage レP Supervisory Circuits |
| MAX6354MRUK-T | Dual/Triple-Voltage レP Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6351MSUK-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual/Triple-Voltage レP Supervisory Circuits |
| MAX6351MSUT | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6351MSUT+T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6351MSUT-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6351MTUK-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual/Triple-Voltage レP Supervisory Circuits |
發布緊急采購，3分鐘左右您將得到回復。