- 您現在的位置：買賣IC網 > PDF目錄224188 > MAX6324HUT44-T (MAXIM INTEGRATED PRODUCTS INC) Analog IC PDF資料下載
參數資料
| 型號： | MAX6324HUT44-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Analog IC |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO6 |
| 封裝： | ROHS COMPLIANT, SOT-23, 6 PIN |
| 文件頁數： | 12/13頁 |
| 文件大小： | 168K |
| 代理商： | MAX6324HUT44-T |
MAX6323/MAX6324
falls below the preset threshold or when the manual
reset input (MR) is asserted. The RESET output remains
asserted for at least 100ms after VCC has risen above
the reset threshold and MR is deasserted (Figure 5).
For noisy environments, bybass VCC with a 500pF (min)
capacitor to ensure correct operation.
The MAX6323 has a push-pull output stage, and the
MAX6324 utilizes an open-drain output. Connect a pull-
up resistor on the RESET output of the MAX6324 to any
supply up to +6V. Select a resistor value large enough
to register a logic low (see
Electrical Characteristics)
and small enough to register a logic high while supply-
ing all input leakage currents and leakage paths con-
nected to the RESET line. A 10k
pullup is sufficient in
most applications.
Manual Reset Input
Many P-based products require manual reset capabil-
ity to allow an operator or external logic circuitry to initi-
ate a reset. The manual reset input (MR) can connect
directly to a switch without an external pullup resistor or
debouncing network. MR is internally pulled up to VCC
and, therefore, can be left unconnected if unused. MR
is designed to reject fast, negative-going transients
(typically 100ns pulses), and it must be held low for a
minimum of 1s to assert the reset output (Figure 5). A
0.1F capacitor from MR to ground provides additional
noise immunity. After MR transitions from low to high,
reset will remain asserted for the duration of the reset
timeout period, at least 100ms.
Applications Information
Negative-Going VCC Transients
The MAX6323/MAX6324 are relatively immune to short-
duration negative-going VCC transients (glitches),
which usually do not require the entire system to shut
down. Typically, 200ns large-amplitude pulses (from
ground to VCC) on the supply will not cause a reset.
Lower amplitude pulses result in greater immunity.
Typically, a VCC transient that falls 100mV below the
reset threshold and lasts less than 20s will not trigger
a reset (see
Typical Operating Characteristics). An
optional 0.1F bypass capacitor mounted close to VCC
provides additional transient immunity.
Ensuring a Valid Reset Output
Down to VCC = 0V
When VCC falls below +1.2V, the MAX6323 RESET out-
put no longer sinks current; it becomes an open circuit.
Therefore, high-impedance CMOS logic inputs con-
nected to RESET can drift to undetermined voltages.
This does not present a problem in most applications,
since most Ps and other circuitry are inoperative with
VCC below +1.2V. However, in applications where
RESET must be valid down to 0, adding a pulldown
resistor to RESET causes any stray leakage currents to
flow to ground, holding RESET low (Figure 6). R1’s
value is not critical; 100k
is large enough not to load
RESET and small enough to pull RESET to ground. This
scheme does not work with the open-drain output of the
MAX6324.
P Supervisory Circuits with Windowed
(Min/Max) Watchdog and Manual Reset
8
_______________________________________________________________________________________
MR
RESET
VCC
VTH
100ms (min)
120ns (typ)
20
s (typ)
1
s (min)
100ms (min)
Figure 5. RESET Timing Relationship
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6581TG98+ | SPECIALTY ANALOG CIRCUIT, QCC24 |
| MAX6768TTLD2+ | 1-CHANNEL POWER SUPPLY SUPPORT CKT, DSO8 |
| MAX6768TTWD4+T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, DSO8 |
| MAX6793TPVD5+ | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC20 |
| MAX6828V+T | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6324HUT46 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX6324HUT46+ | 制造商:Maxim Integrated Products 功能描述:MAXIM MAX6324HUT46+ PROCESSOR SUPERVISORS - Boxed Product (Development Kits) 制造商:Maxim Integrated Products 功能描述:Maxim MAX6324HUT46+ Processor Supervisors |
| MAX6324HUT46+T | 功能描述:監控電路 uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6324HUT46-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6325CPA | 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓撲結構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。