- 您現在的位置：買賣IC網 > PDF目錄224188 > MAX6324GUT31-T (MAXIM INTEGRATED PRODUCTS INC) Analog IC PDF資料下載
參數資料
| 型號： | MAX6324GUT31-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Analog IC |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO6 |
| 封裝： | ROHS COMPLIANT, SOT-23, 6 PIN |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 168K |
| 代理商： | MAX6324GUT31-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁
MAX6323/MAX6324
P Supervisory Circuits with Windowed
(Min/Max) Watchdog and Manual Reset
_______________________________________________________________________________________
5
500
s/div
MAX6323/24-10
WDI
2V/div
WDPO
FAST WATCHDOG TIMEOUT PERIOD
MAX6323AUT23
5ms/div
MAX6323/24-11
WDI
2V/div
WDPO
SLOW WATCHDOG TIMEOUT PERIOD
MAX6323AUT23
Typical Operating Characteristics (continued)
(VCC = full range, TA = +25°C, unless otherwise noted.)
Pin Description
Active-Low. Reset is asserted when VCC drops below VTH and remains asserted until VCC rises above VTH
for the duration of the reset timeout period. The MAX6323 has a push-pull output and the MAX6324 has an
open-drain output. Connect a pullup resistor from RESET to any supply voltage up to +6V.
Watchdog Pulse Output. The open-drain WDPO output is pulsed low for 1ms (typ) upon detection of a fast
or slow watchdog fault. WDPO is only active when RESET is high.
WDPO
5
RESET
6
Supply Voltage for the Device. Input for VCC reset monitor. For noisy systems, bypass VCC with a 500pF
(min) capacitor.
VCC
4
Watchdog Input. The internal watchdog timer clears to zero on the falling edge of WDI or when RESET goes
high. If WDI sees another falling edge within the factory-trimmed watchdog window, WDPO will remain
unasserted. Transitions outside this window, either faster or slower, will cause WDPO to pulse low for 1ms
(typ).
WDI
3
PIN
Ground
GND
2
Active-Low, Manual Reset Input. When MR is asserted low, RESET is asserted low, the internal watchdog
timer is reset to zero, and WDPO is reset to high impedance (open drain). After the rising edge of MR,
RESET is asserted for at least 100ms. Leave MR unconnected or connect to VCC if unused.
MR
1
FUNCTION
NAME
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6324GUT44-T | Analog IC |
| MAX6324GUT46-T | Analog IC |
| MAX6324HUT23-T | Analog IC |
| MAX6324HUT26-T | Analog IC |
| MAX6324HUT29-T | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6324GUT44 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Cut Tape Product |
| MAX6324GUT44+T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6324GUT44-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6324GUT46 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Cut Tape Product |
| MAX6324GUT46+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.63V 27UA 6PIN SOT-23 - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。