
MAX6037_25 OUTPUT VOLTAGE
vs. TEMPERATURE (V
OUT
= 2.500V)
M
TEMPERATURE (
°
C)
O
100
75
-25
0
25
50
2.4925
2.4950
2.4975
2.5000
2.5025
2.5050
2.5075
2.5100
2.4900
-50
125
MAX6037_12 SUPPLY CURRENT
vs. INPUT VOLTAGE (V
OUT
= 1.25V)
M
INPUT VOLTAGE (V)
S
μ
A
5.0
4.5
4.0
3.5
3.0
180
190
200
210
220
230
170
2.5
5.5
T
A
= +125
°
C
T
A
= +25
°
C
T
A
= -40
°
C
MAX6037_12 SUPPLY CURRENT
vs. TEMPERATURE (V
OUT
= 1.25V)
M
TEMPERATURE (
°
C)
S
μ
A
100
75
50
25
0
-25
175
200
225
250
150
-50
125
V
IN
= +2.5V
V
IN
= +5.5V
Typical Operating Characteristics
(V
IN
= +3V for the MAX6037_12 and MAX6037_21; V
IN
= +5V for the MAX6037_25, MAX6037_30, MAX6037_33, and MAX6037_41;
I
OUT
= 0, C
OUT
= 0.1μF, C
IN
= 0.1μF, T
A
= +25°C, unless otherwise specified.)
M
Low-Power, Fixed and Adjustable Reference
with Shutdown in SOT23
10
______________________________________________________________________________________
Note 1:
Note 2:
Note 3:
All devices are 100% tested at T
A
= +25
°
C and are guaranteed by design for T
A
= T
MIN
to T
MAX
, as specified.
Temperature coefficient is measured by the “box” method, i.e., the maximum
V
OUT
/ V
OUT
is divided by the maximum
T.
Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from T
MAX
to
T
MIN
.
Not production tested. Guaranteed by design.
Dropout voltage is defined as the minimum differential voltage (V
IN
- V
OUT
) at which V
OUT
decreases by 1% from its origi-
nal value at V
IN
= +5.0V.
V
OUT
initial accuracy for the MAX6037_ADJ is tested with ADJ shorted to OUT. Actual accuracy will be affected by match-
ing and the temperature coefficient of the external resistors used. Use 1% resistors with low temperature coefficient for
best overall accuracy.
The temperature coefficient for the MAX6037_ADJ is specified for the case where ADJ is connected to OUT. For the case
where an external resistive network is used to set the output voltage, actual change in reference output over temperature
will be affected by the temperature coefficient and matching of the external resistors used.
The minimum V
IN
is the greater of +2.5V and (V
OUT
+ 0.2V).
V
OUT
set to +5V with an external resistive-divider.
Note 10:
Noise for the MAX6037_ADJ is specified for a +1.25V output. Noise is proportional to V
OUT
and is greater for higher output
voltages. In addition, external resistors used to set the output voltage can contribute to noise.
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SHUTDOWN (
SHDN
)
Logic-High Input Voltage
Logic-Low Input Voltage
Logic-High Input Current
Logic-Low Input Current
V
ENH
V
ENL
I
ENH
I
ENL
2.5V
≤
V
IN
≤
5.5V
2.5V
≤
V
IN
≤
5.5V
2.5V
≤
V
IN
≤
5.5V, V
SHDN
= V
IN
2.5V
≤
V
IN
≤
5.5V, V
SHDN
= 0V
2.0
V
V
nA
nA
0.7
-1000
-1000
0.15
0.05
+1000
+1000
ELECTRICAL CHARACTERISTICS—MAX6037_ADJ (V
OUT
= 1.184V to 5V) (continued)
(V
IN
= V
SHDN
= +5V, I
OUT
= 0, T
A
= T
MIN
to T
MAX
, ADJ shorted to OUT unless otherwise noted. Typical values are at T
A
= +25°C.)
(Note 1)