參數資料
型號： MAX5953DUTM+
廠商： Maxim Integrated
文件頁數： 17/27頁
文件大?。?/td> 371K
描述： IC INTERFACE 802.3AF 48TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 43
類型： 以太網供電開關（PoE）
應用： 遠程外設（工業控制，相機，數據訪問）
內部開關： 是
電源電壓： 11 V ~ 76 V
工作溫度： 0°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-WFQFN 裸露焊盤
供應商設備封裝： 48-TQFN-EP（7x7）
包裝： 管件
The two-switch power topology recovers energy stored
in both the magnetizing and the parasitic leakage induc-
tances of the transformer. The Typical Application
Circuit, Figure 3, shows the schematic diagram of a -48V
input flyback converter using the MAX5953A. Figure 4
shows the schematic diagram of a -48V input forward
converter and a 5V, 3A output isolated power supply.
Voltage-Mode Control and the PWM Ramp
For voltage-mode control, the feed-forward PWM ramp
is generated at RCFF. From RCFF, connect a capacitor
to GND and a resistor to HVIN. The ramp generated is
applied to the noninverting input of the PWM compara-
tor at RAMP and has a minimum voltage of approxi-
mately 2V. The slope of the ramp is determined by the
voltage at HVIN and affects the overall loop gain. The
ramp peak must remain below the 5.5V dynamic range
of RCFF. Assuming the maximum duty cycle approach-
es 50% at a minimum input voltage (PWM UVLO turn-
on threshold), use the following formula to calculate the
minimum value of either the ramp capacitor or resistor:
where f
S
is the switching frequency, V
R(P-P)
is the peak-
to-peak ramp voltage (2V, typ). Select R
RCFF
resistance
value between 200k& and 600k&.
Maximize the signal-to-noise ratio by setting the ramp
peak as high as possible. Calculate the low-frequency,
small-signal gain of the power stage (the gain from the
inverting input of the PWM comparator to the output)
using the following formula:
G
PS
= N
SP
x R
RCFF
x C
RCFF
x f
S
where N
SP
is the secondary to primary power trans-
former turns ratio.
Secondary-Side Synchronization
The MAX5953A/MAX5953B/MAX5953C/MAX5953D
provide convenient synchronization for optional sec-
ondary-side synchronous rectifiers. Figure 5 shows the
connection diagram with a high-speed optocoupler.
Choose an optocoupler with a propagation delay of
less than 80ns. The synchronizing pulse is generated
approximately 110ns ahead of the main pulse that dri-
ves the two power MOSFETs.
Undervoltage Lockout for DC-DC Converter
Connect PGOOD to DCUVLO to ensure the PD interface
is ready prior to the DC-DC converter. The DCUVLO
block monitors the input voltage at HVIN through an
external resistive divider (R16 and R17) connected to
DCUVLO (see Figure 3). Use the following equation to
calculate R16 and R17:
where V
DCUVLOIN
is the desired input voltage lockout
level and V
DCUVLO
is the undervoltage lockout thresh-
old (1.25V, typ). Select the R17 resistance value
between 100k& and 500k&.
Optocoupled Feedback
Isolated voltage feedback is achieved by using an
optocoupler as shown in Figure 3. Connect the collec-
tor of the optotransistor to OPTO and a pullup resistor
between OPTO and REGOUT.
Internal Regulators
As soon as power is provided to HVIN, internal power
supplies power the DCUVLO detection circuitry.
REGOUT is used to drive the internal power MOSFETs.
Bypass REGOUT to GND with a minimum 2.2礔 ceram-
ic capacitor. The HVIN LDO steps down V
HVIN
to a
nominal output voltage (V
REGOUT
) of 8.75V. A second
parallel LDO powers REGOUT from INBIAS. A tertiary
winding connected through a diode to INBIAS powers
up REGOUT once switching commences. This powers
REGOUT to 10.5V (typ) and shuts off the current flow-
ing from HVIN to REGOUT. This results in a lower on-
chip power dissipation and higher efficiency.
V
V
R
R
DCUVLOIN
DCUVLO
=
?nbsp  +
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
1
16
17
R
C
V
f   V
RCFF
RCFF
IN EX
S    R P  P
?/DIV>
e
?nbsp  ?/DIV>

,
2
IEEE 802.3af PD Interface and PWM Controllers
with Integrated Power MOSFETs
______________________________________________________________________________________   17
C
+5V
R
MAX5953A
MAX5953B
MAX5953C
MAX5953D
PPWM
PGND
Figure 5. Secondary-Side Synchronous Rectifier Driver Using a
High-Speed Optocoupler
相關PDF資料
PDF描述
MAX5954LETX+T IC PCI EXP/HOT-PLUG CTRLR 36TQFN
MAX5955BEEE+ IC DUAL HOT-SWAP CTRLR 16-QSOP
MAX5957AETN+T IC TRPL PCI EXP/HOT-PLUG 56-TQFN
MAX5960AECS+T IC CTRLR HOT-PLUG QD 80-TQFP
MAX5963UTL+T IC HOT SWAP DIO ORING CTL 40TQFN
相關代理商/技術參數
參數描述
MAX5953DUTM+ 功能描述:電壓模式 PWM 控制器 IEEE 802.3af PD Int & PWM Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
MAX5953DUTM+T 功能描述:電壓模式 PWM 控制器 IEEE 802.3af PD Int & PWM Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
MAX5954AETX+ 功能描述:熱插拔功率分布 Single PCIe Hot Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5954AETX+T 功能描述:熱插拔功率分布 Single PCIe Hot Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5954LETX+ 功能描述:熱插拔功率分布 Single PCIe Hot Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*