參數資料
型號: MAX5946AETX
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 電源管理
英文描述: Dual PCI Express, Hot-Plug Controller
中文描述: 2-CHANNEL POWER SUPPLY SUPPORT CKT, QCC36
封裝: 6 X 6 MM, 0.90 MM HEIGHT, MO-220, QFN-36
文件頁數: 16/23頁
文件大?。?/td> 1019K
代理商: MAX5946AETX
M
12V and 3.3V Outputs Normal Operation
The MAX5946 monitors and actively limits the current of
the 12V and 3.3V outputs after the startup period. Each
output has its own overcurrent threshold. If any of the
monitored output currents rise above the overcurrent
threshold for a period t
FAULT
,
FAULT_
asserts and the
controller disengages both the 12V and 3.3V outputs for
the particular slot (see the
Fault Management
section).
3.3V Auxiliary Output Normal Operation
The auxiliary output current is internally monitored and
actively limited to the maximum current-limit value. An
overcurrent fault condition occurs when the output
current exceeds the overcurrent threshold for longer
then t
FAULT
. A fault on an auxiliary channel causes all
supplies of the affected channel to be disabled after a
programmable time period t
FAULT
(see the
Fault
Management
section).
Power-Good (
PWRGD_
)
Power-good (
PWRGD_
) is an open-drain output that
pulls low a time (t
POR_HL
) after all of the outputs of the
respective slot are fully on. All outputs are considered
fully on when 3.3G_ has risen to V
PGTH3.3
, 12G_ has
risen to V
PGTH12
, and V
3.3AUXO_
is less then
V
PGTH3.3AUX
. t
POR_HL
is adjustable from 2.5ms to
1.5s by connecting a resistor from PORADJ to GND.
See the
Setting the Power-On-Reset Timeout Period
(t
POR
)
section.
Thermal Shutdown
When the die temperature goes above (T
SD
) +150°C, an
overtemperature fault occurs and the MAX5946 shuts
down all outputs. The device waits for the junction temper-
ature to decrease below T
SD
- Hysteresis before entering
fault management (see the
Fault Management
section).
Dual PCI Express, Hot-Plug
Controller
16
______________________________________________________________________________________
V
ON_,TH
ON_, AUXON_
PWRGD_
FAULT_
12G_, 3.3G_
12VO_, 3.3VO_
3.3VAUXO_
V
PGTH12
V
PGTH3.3
V
PGTH3.3AUX
3.3AUXIN
RISING
EDGE
PWRGD_ IS PULLED UP TO 3.3.
FAULT_ IS PULLED UP TO 3.3AUXIN.
t
POR_HL
Figure 2. Power-Up Timing, No Fault
FAULT_
3.3VAUXIN
RISING
EDGE
PWRGD_ IS PULLED UP TO 3.3VAUXO_.
FAULT_ IS PULLED UP TO 3.3VAUXIN.
A FAULT ON THE 3.3V OUTPUT OR 3.3VAUXO_ OUTPUT PRODUCES SIMILAR RESULTS.
V
ON_,TH
ON_
2 x t
FAULT
PWRGD_
12G_
12V OUTPUT
CURRENT
3.3VAUXO_
V
12ILIM,TH
R
SENSE
Figure 3. 12V Power-Up Timing (Turn-On into Output
Overcurrent/Short Circuit)
FAULT_
PWRGD_ IS PULLED UP TO 3.3VAUXO_.
FAULT_ IS PULLED UP TO 3.3VAUXIN.
A FAULT ON THE 3.3V OUTPUT OR 3.3VAUXO_ OUTPUT PRODUCES SIMILAR RESULTS.
t
FAULT
PWRGD_
12G_
12V OUTPUT
CURRENT
V
12ILIM,TH
R
SENSE
Figure 4. 12 Output Overcurrent/Short Circuit During Normal
Operation
相關PDF資料
PDF描述
MAX5946LETX Dual PCI Express, Hot-Plug Controller
MAX6002EUR IC-SM-2.5V VOLTAGE REFERENCE
MAX6004EUR IC-SM-4.096V VOLTAGE REFERENCE
MAX6023EBK30-T Analog IC
MAX6023EBK41-T Analog IC
相關代理商/技術參數
參數描述
MAX5946AETX+ 功能描述:熱插拔功率分布 Dual PCIe Hot-Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5946AETX+T 功能描述:熱插拔功率分布 Dual PCIe Hot-Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5946AETX-T 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5946LETJ 制造商:Maxim Integrated Products 功能描述:DUAL PCI-EXPRESS HOT-PLUG CONTROLLER - Rail/Tube
MAX5946LETX 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube