參數資料
型號： MAX5929BEEG+
廠商： Maxim Integrated
文件頁數： 13/23頁
文件大?。?/td> 340K
描述： IC HOT SWAP CTLR QUAD 24QSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： 熱交換控制器
應用： 通用
內部開關： 無
電源電壓： 1 V ~ 15 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 24-QSOP
包裝： 管件
The MAX5927A/MAX5929AMAX5929D turn off all
channels if any of the above conditions are not met.
After a fault-latched shutdown, cycle any of the ON_
inputs to unlatch and restart all channels, depending
on the corresponding V
ON_
state.
Independent Mode
Connect MODE to GND to enter independent mode.
While in independent mode, the MAX5927A/
MAX5929AMAX5929D provide complete independent
control for each channel. To turn on a given channel:
"  At least one V
IN_
must exceed V
UVLO
(2.45V) for the
UVLO to startup delay (37.5ms).
"  The corresponding V
IN_
must exceed V
PWRRDY
(0.95V).
"  The corresponding V
ON_
must exceed V
ON,TH
(0.875V).
The MAX5927A/MAX5929AMAX5929D turn off the cor-
responding channel if any of the above conditions are
not met. During a fault condition on a given channel only,
the affected channel is disabled. After a fault-latched
shutdown, recycle the corresponding ON_ inputs to
unlatch and restart only the corresponding channel.
Startup Period
R
TIM
sets the duration of the startup period from 0.4ms
(R
TIM
= 4k? to 50ms (R
TIM
= 500k? (see the Setting
the Startup Period, R
TIM
section). The default startup
period is fixed at 9ms when TIM is floating. The startup
period begins after the turn-on conditions are met as
described in the Mode section, and the device is not
latched or in its autoretry delay (see the Latched and
Autoretry Fault Management section).
The MAX5927A/MAX5929AMAX5929D limit the load
current if an overcurrent fault occurs during startup
instead of completely turning off the external MOSFETs.
The slow comparator is disabled during the startup
period and the load current can be limited in two ways:
1) Slowly enhancing the MOSFETs by limiting the
MOSFET gate-charging current.
2) Limiting the voltage across the external current-
sense resistor.
During the startup period, the gate-drive current is limit-
ed to 100礎 and decreases with the increase of the
gate voltage (see the Typical Operating Characteristics).
This allows the controller to slowly enhance the
MOSFETs. If the fast comparator detects an overcur-
rent, the MAX5927A/MAX5929AMAX5929D regulate
the gate voltage to ensure that the voltage across the
sense resistor does not exceed V
SU,TH
. This effectively
regulates the inrush current during startup.
Figure 6 shows the startup waveforms. STAT_ is assert-
ed immediately after the startup period if no fault condi-
tion is present.
VariableSpeed/BiLevel Fault Protection
VariableSpeed/BiLevel fault protection incorporates
comparators with different thresholds and response
times to monitor the load current (Figure 7). During the
startup period, protection is provided by limiting the
load current. Protection is provided in normal operation
(after the startup period has expired) by discharging
the MOSFET gates with a 3mA/50mA pulldown current
in response to a fault condition. After a fault, STAT_ is
deasserted, the MAX5929A/MAX5929B stays latched
off and the MAX5929C/MAX5929D automatically
restart. Use the MAX5927A LATCH input to control
whether the STAT_ outputs latch off or autoretry after a
fault condition (see the Latched and Autoretry Fault
Management section).
Low-Voltage, Quad, Hot-Swap
Controllers/Power Sequencers
_______________________________________________________________________________________________________________________________________________________________________________________________________  _____   13
Figure 4. Power-Sequencing Fault Turn-Off
ON1 = ON2 = ON3 = ON4
OVERCURRENT
FAULT
CONDITION
OUT1
OUT2
OUT3
OUT4
*THE OUT_ DISCHARGE RATE IS A RESULT OF NATURAL DECAY
  OF THE LOAD RESISTANCE AND CAPACITANCE.
*
*
*
*
相關PDF資料
PDF描述
MAX5930AEEG+ IC HOT SWAP CTLR PWR SEQ 24QSOP
MAX5932ESA+T IC HOT-SWAP CONTROLLER 8-SOIC
MAX5933EESA+ IC HOT-SWAP CONTROLLER 8-SOIC
MAX5934EEE+ IC HOT-SWAP CONTROLLER 16-QSOP
MAX5935EAX+ IC CTRLR POWER QUAD 36-SSOP
相關代理商/技術參數
參數描述
MAX5929BEEG+ 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5929BEEG+T 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5929CEEG+ 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5929CEEG+T 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MAX5929DEEG+ 功能描述:熱插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*