- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5916EUI+ (Maxim Integrated)IC HOT-SWAP CTRLR DUAL 28-TSSOP Datasheet資料下載
參數資料
| 型號： | MAX5916EUI+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 14/25頁 |
| 文件大?。?/td> | 488K |
| 描述： | IC HOT-SWAP CTRLR DUAL 28-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 熱交換控制器 |
| 應用： | PCI 2.2 服務器 |
| 內部開關： | 無 |
| 電源電壓： | 10.8 V ~ 13.2 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
Input Undervoltage Lockout
UVLO prevents these devices from turning on
internal/external MOSFETs until the input voltage exceeds
the lockout threshold. The UVLO protects the MOSFETs
from insufficient gate-drive voltage. Figure 2 shows that if
an input undervoltage condition exists for more than
t
DEG,UVLO
, the outputs are disabled and PGOOD_ goes
low immediately. The time delay t
DEG,UVLO
is negative
edge delayed and acts as a deglitch.
Fault Management
When a fault is detected on one of the main outputs, the
MAX5915/MAX5915A/MAX5916/MAX5916A disable the
channel outputs after t
DELAY
. A fault occurs when any of
the output voltages fall below their output undervoltage
threshold or any of the output currents exceed their out-
put overcurrent threshold. PGOOD_ pulls low if a fault
persists for more than t
RESP
. The channel with the fault is
disabled after t
DELAY
. The MAX5915/MAX5916 are avail-
able with a response time of 1.5ms (t
RESP
). The
MAX5915A/MAX5916A offer a response time of 100ns
(t
RESP2
). If the fault is removed before t
DELAY
, the chan-
nel remains on and PGOOD_ pulls high immediately.
Latched Fault Protection
The MAX5915/MAX5915A latch off the appropriate
channels main outputs. Toggling +12VIN or ON_
restarts the main outputs. Figure 3 outlines the logic for
the main and auxiliary shutdown control of the
MAX5915, while fault handling is shown in Figures 5
and 6.
Autoretry Fault Protection
The MAX5916/MAX5916A automatically restart the out-
puts after t
RESTART
. The MAX5915/MAX5915A/
MAX5916/MAX5916A handle faults on the auxiliary out-
puts by automatically restarting the appropriate chan-
nel. Figure 4 outlines the logic for the main and auxiliary
shutdown control of the MAX5916, while fault handling
is shown in Figures 6 and 7.
Output Overcurrent
External sense resistors monitor the current on the +5V
and +3.3V outputs, while the +3.3V auxiliary and ?2V
output currents are monitored internally. Figures 5, 6,
and 7 show overcurrent fault management for the
MAX5915/MAX5915A/MAX5916/MAX5916A.
Dual PCI 2.2 Hot-Swap Controllers
14 ______________________________________________________________________________________
ON_
+12VIN
3.3VAUXIN
PGOOD_
AUXON_
+12V UVLO THRESHOLD
3.3VAUX UVLO THRESHOLD
t
START
t
START
t
DEG.UVLO
t
DEG.UVLO
+12VO_
5VO_
3.3VO_
3.3VAUXO_
-12VO_
TIMING NOT TO SCALE
Figure 2. Input UVLO Fault Management in the MAX5915/MAX5915A/MAX5916/MAX5916A
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5917BESE+ | IC HOT-SWAP SWITCH 65V 16-SOIC |
| MAX5920BESA+ | IC HOT-SWAP CTRLR -48V 8-SOIC |
| MAX5922AEUI+ | IC NETWORK PWR SW +48V 28-TSSOP |
| MAX5923EUP+T | IC HOT-SWAP SWITCH +60V 20-TSSOP |
| MAX5926EEE+ | IC HOT-SWAP CONTROLLER 16QSOP-EP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5916EUI+ | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916EUI+T | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916EUI-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916UUI+ | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916UUI+T | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。