- 您現在的位置：買賣IC網 > PDF目錄384688 > MAX5916 (Maxim Integrated Products, Inc.) Quadruple 2-Line To 1-Line Data Selectors/Multiplexers 16-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX5916 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Quadruple 2-Line To 1-Line Data Selectors/Multiplexers 16-CDIP -55 to 125 |
| 中文描述： | 雙路PCI 2.2熱插拔控制器 |
| 文件頁數： | 13/25頁 |
| 文件大?。?/td> | 579K |
| 代理商： | MAX5916 |
channel outputs, auxiliary and main. A fault condition
occurs when the output voltage falls below the set
undervoltage threshold or the output current reaches the
overcurrent threshold. When a fault occurs, all supplies
of the affected channel are disabled after a time period
t
DELAY
. All outputs are automatically restarted after a
time equal to t
RESTART
. This reset is built into all devices.
Current Limits
All supplies are protected against output overcurrent or
short-circuit conditions. The MAX5915/MAX5915A and
MAX5916/MAX5916A employ a
“
brickwall
”
current limit
on the +3.3V and +5V supplies and a current-foldback
scheme on the ±12V and +3.3V auxiliary supplies.
Brickwall
A brickwall current limit protects the +3.3V and +5V
main supplies by limiting the load current. The external
sense resistors and the current-limit threshold set the
brickwall current limits. A fault occurs when the load
current reaches the brickwall limit. The main outputs
shut down after t
DELAY
if the fault remains. The brick-
wall feature limits inrush current caused by positive
supply voltage steps.
Foldback
The ±12V and +3.3V auxiliary supplies employ an
internal current-foldback scheme. The MAX5915/
MAX5915A/MAX5916/MAX5916A gradually limit the load
current once the current-foldback threshold is reached. If
the overcurrent condition lasts longer than a fast tran-
sient, the output current is reduced to the foldback cur-
rent limit and remains at that level for t
DELAY
unless the
overcurrent condition is cleared. See the
Typical
Operating Characteristics
.
M
Dual PCI 2.2 Hot-Swap Controllers
______________________________________________________________________________________
13
t
START
ON_
+12VIN
3.3VAUX UVLO THRESHOLD
3.3VAUXIN
PGOOD_
TIMING NOT TO SCALE
AUXON_
+12V
UVLO THRESHOLD
+12VO_
-12VO_
5VO_
3.3VO_
3.3VAUXO_
Figure 1. Startup Waveforms
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5916A | Dual PCI 2.2 Hot-Swap Controllers |
| MAX5916AEUI | Dual PCI 2.2 Hot-Swap Controllers |
| MAX5916EUI | Dual PCI 2.2 Hot-Swap Controllers |
| MAX5917BESE | +65V Simple Swapper Hot-Swap Switches |
| MAX5910 | +65V Simple Swapper Hot-Swap Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5916AEUI | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916AEUI+ | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916AEUI+T | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916AEUI-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5916AUUI+ | 功能描述:熱插拔功率分布 Dual PCI 2.2 Hot Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。