- 您現在的位置：買賣IC網 > PDF目錄10844 > MAX5873EGK+TD (Maxim Integrated Products)IC DAC 12BIT DUAL 200MSPS 68-QFN PDF資料下載
參數資料
| 型號： | MAX5873EGK+TD |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/16頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT DUAL 200MSPS 68-QFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 設置時間： | 14ns |
| 位數： | 12 |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 300mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 68-QFN 裸露焊盤（10x10） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 4 電流，單極 |
| 采樣率（每秒）： | 200M |
MAX5873
12-Bit, 200Msps, High-Dynamic-Performance,
Dual DAC with CMOS Inputs
______________________________________________________________________________________
13
Differential Coupling Using a Wideband RF
Transformer
Use a pair of transformers (Figure 6) or a differential
amplifier configuration to convert the differential voltage
existing between OUTIP/OUTQP and OUTIN/OUTQN to
a single-ended voltage. Optimize the dynamic perfor-
mance by using a differential transformer-coupled out-
put to limit the output power to < 0dBm full scale. Pay
close attention to the transformer core saturation char-
acteristics when selecting a transformer for the
MAX5873. Transformer core saturation can introduce
strong 2nd-order harmonic distortion especially at low
output frequencies and high signal amplitudes. For best
results, center tap the transformer to ground. When not
using a transformer, terminate each DAC output to
ground with a 25 resistor. Additionally, place a 50
resistor between the outputs (Figure 7).
For a single-ended unipolar output, select OUTIP
(OUTQP) as the output and ground OUTIN (OUTQN) to
GND. Driving the MAX5873 single-ended is not recom-
mended since additional noise and distortion will
be added.
The distortion performance of the DAC depends on the
load impedance. The MAX5873 is optimized for 50
differential double termination. It can be used with a
transformer output as shown in Figure 6 or just one 25
resistor from each output to ground and one 50 resis-
tor between the outputs (Figure 7). This produces a full-
scale output power of up to -2dBm, depending on the
output current setting. Higher termination impedance
can be used at the cost of degraded distortion perfor-
mance and increased output noise voltage.
Grounding, Bypassing, and Power-
Supply Considerations
Grounding and power-supply decoupling can strongly
influence the MAX5873 performance. Unwanted digital
crosstalk couples through the input, reference, power
supply, and ground connections, and affects dynamic
performance. High-speed, high-frequency applications
require closely followed proper grounding and power-
supply decoupling. These techniques reduce EMI and
internal crosstalk that can significantly affect the
MAX5873 dynamic performance.
Use a multilayer PCB with separate ground and power-
supply planes. Run high-speed signals on lines directly
above the ground plane. Keep digital signals as far
away from sensitive analog inputs and outputs, refer-
ence input sense lines, common-mode input, and clock
inputs as practical. Use a symmetric design of clock
input and the analog output lines to minimize 2nd-order
harmonic distortion components, thus optimizing the
DAC’s dynamic performance. Keep digital signal paths
short and run lengths matched to avoid propagation
delay and data skew mismatches.
WIDEBAND RF TRANSFORMER
PERFORMS SINGLE-ENDED-TO-
DIFFERENTIAL CONVERSION
SINGLE-ENDED
CLOCK SOURCE
GND
1:1
25
CLKP
CLKN
TO DAC
0.1F
Figure 5. Differential Clock-Signal Generation
MAX5873
12
OUTIP/OUTQP
OUTIN/OUTQN
DATA11–DATA0
WIDEBAND RF TRANSFORMER T2 PERFORMS THE
DIFFERENTIAL-TO-SINGLE-ENDED CONVERSION
T1, 1:1
T2, 1:1
GND
50
100
50
VOUT, SINGLE-ENDED
Figure 6. Differential-to-Single-Ended Conversion Using a Wideband RF Transformer
相關PDF資料 |
PDF描述 |
|---|---|
| RM12BJB-5PH | RM 12 JACK 5 POS. W/PIN |
| MAX5151BCEE+ | IC DAC 13BIT DUAL LP SER 16-QSOP |
| MAX508BCWP+T | IC DAC 12BIT W/REF 20-SOIC |
| MAX5152BCEE+ | IC DAC 13BIT DUAL LP SER 16-QSOP |
| MAX5153BCEE+ | IC DAC 13BIT DUAL LP SER 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5873EVKIT | 功能描述:數模轉換器- DAC Evaluation Kit for the MAX5873 MAX5874 MAX5875 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5874EGK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX5874EGK+D | 功能描述:數模轉換器- DAC 14-Bit 2Ch 200Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5874EGK+TD | 功能描述:數模轉換器- DAC 14-Bit 2Ch 200Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5874EGK-D | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。