- 您現在的位置：買賣IC網 > PDF目錄10754 > MAX5865ETM+ (Maxim Integrated Products)IC ANLG FRONT END 40MSPS 48-TQFN PDF資料下載
參數資料
| 型號： | MAX5865ETM+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ANLG FRONT END 40MSPS 48-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 43 |
| 位數： | 10 |
| 通道數： | 4 |
| 功率（瓦特）： | 2.10W |
| 電壓 - 電源，模擬： | 2.7 V ~ 3.3 V |
| 電壓 - 電源，數字： | 1.8 V ~ 3.3 V |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-TQFN-EP（7x7） |
| 包裝： | 管件 |
| 產品目錄頁面： | 1398 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
MAX5865
Ultra-Low-Power, High-Dynamic-
Performance, 40Msps Analog Front End
22
___________________________________________________________________________________________________
0
2
1
4
3
7
6
5
000
010
001
011
100
101
110
AT STEP
011 (1/2 LSB )
AT STEP
001 (1/4 LSB )
111
DIGITAL INPUT CODE
ANALOG
OUTPUT
VALUE
Figure 12a. Integral Nonlinearity
0
2
1
4
3
6
5
000
010
001
011
100
101
DIFFERENTIAL LINEARITY
ERROR (-1/4 LSB)
DIFFERENTIAL
LINEARITY ERROR (+1/4 LSB)
1 LSB
DIGITAL INPUT CODE
ANALOG
OUTPUT
VALUE
Figure 12b. Differential Nonlinearity
range, it can interface directly with RF transceivers while
eliminating discrete components and amplifiers used for
level-shifting circuits. Also, the DAC’s full dynamic range
is preserved because the internally generated common-
mode level eliminates code-generated level shifting or
attenuation due to resistor level shifting. The MAX5865
ADC has 1VP-P full-scale range and accepts input com-
mon-mode levels of VDD/2 (
±200mV). These features
simplify the analog interface between RF quadrature
demodulator and ADC while eliminating discrete gain
amplifiers and level-shifting components.
Grounding, Bypassing, and
Board Layout
The MAX5865 requires high-speed board layout design
techniques. Refer to the MAX5865 EV kit data sheet for
a board layout reference. Locate all bypass capacitors
as close to the device as possible, preferably on the
same side of the board as the device, using surface-
mount devices for minimum inductance. Bypass VDD to
GND with a 0.1F ceramic capacitor in parallel with a
2.2F capacitor. Bypass OVDD to OGND with a 0.1F
ceramic capacitor in parallel with a 2.2F capacitor.
Bypass REFP, REFN, and COM each to GND with a
0.33F ceramic capacitor. Bypass REFIN to GND with
a 0.1F capacitor.
Multilayer boards with separated ground and power
planes yield the highest level of signal integrity. Use a
split ground plane arranged to match the physical loca-
tion of the analog ground (GND) and the digital output
driver ground (OGND) on the device package. Connect
the MAX5865 exposed backside paddle to the GND
plane. Join the two ground planes at a single point
such that the noisy digital ground currents do not inter-
fere with the analog ground plane. The ideal location
for this connection can be determined experimentally at
a point along the gap between the two ground planes.
Make this connection with a low-value, surface-mount
resistor (1
to 5), a ferrite bead, or a direct short.
Alternatively, all ground pins could share the same
ground plane, if the ground plane is sufficiently isolated
from any noisy digital system’s ground plane (e.g.,
downstream output buffer or DSP ground plane).
Route high-speed digital signal traces away from sensi-
tive analog traces. Make sure to isolate the analog
input lines to each respective converter to minimize
channel-to-channel crosstalk. Keep all signal lines short
and free of 90
° turns.
Dynamic Parameter Definitions
ADC and DAC Static Parameter Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from a straight line. This straight
line can be either a best-straight-line fit or a line drawn
between the end points of the transfer function, once
offset and gain errors have been nullified. The static lin-
earity parameters for the device are measured using
the end-point method. (DAC Figure 12a).
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step width and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes (ADC) and a monotonic transfer function
(ADC and DAC) (DAC Figure 12b).
ADC Offset Error
Ideally, the midscale transition occurs at 0.5 LSB above
midscale. The offset error is the amount of deviation
between the measured transition point and the ideal
transition point.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J3P-MY-F4 | CONVERTER MOD DC/DC 13.8V 50W |
| 73M1903-IM/F | IC MODEM AFE V.22BIS 32-QFN |
| VE-J3P-MY-F3 | CONVERTER MOD DC/DC 13.8V 50W |
| ISL51002CQZ-165 | IC FRONT END 10BIT VID 128-MQFP |
| VE-J3P-MY-F1 | CONVERTER MOD DC/DC 13.8V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5865ETM+ | 功能描述:ADC / DAC多通道 10-Bit 2Ch 40Msps CODEC/AFE RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5865ETM+T | 功能描述:ADC / DAC多通道 10-Bit 2Ch 40Msps CODEC/AFE RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5865ETM-D | 制造商:Maxim Integrated Products 功能描述:DUAL 10BIT DAC & DUAL 8BIT ADC 40MSPS CODEC - Rail/Tube |
| MAX5865ETM-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX5865EVKIT | 功能描述:數據轉換 IC 開發工具 Evaluation Kit for the MAX5863 MAX5864 MAX5865 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。