Output DACs with Internal Reference and I
參數資料
型號： MAX5815AAUD+
廠商： Maxim Integrated Products
文件頁數： 19/30頁
文件大?。?/td> 0K
描述： IC DAC 12BIT SRL 4CH 14TSSOP
產品培訓模塊： Obsolescence Mitigation Program
標準包裝： 96
設置時間： 4.5µs
位數： 12
數據接口： I²C，串行
轉換器數目： 4
電壓電源： 模擬和數字
功率耗散（最大）： 797mW
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 14-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 14-TSSOP
包裝： 管件
輸出數目和類型： 4 電壓，單極
MAX5813/MAX5814/MAX5815
Ultra-Small, Quad-Channel, 8-/10-/12-Bit Buffered
Output DACs with Internal Reference and I2C Interface
26
Maxim Integrated
Applications Information
Power-On Reset (POR)
When power is applied to VDD and VDDIO, the DAC out-
put is set to zero scale. To optimize DAC linearity, wait
until the supplies have settled and the internal setup and
calibration sequence completes (200Fs, typ).
Power Supplies and
Bypassing Considerations
Bypass VDD and VDDIO with high-quality ceramic capac-
itors to a low-impedance ground as close as possible to
the device. Minimize lead lengths to reduce lead induc-
tance. Connect the GND to the analog ground plane.
Layout Considerations
Digital and AC transient signals on GND can create noise
at the output. Connect GND to form the star ground for
the DAC system. Refer remote DAC loads to this system
ground for the best possible performance. Use proper
grounding techniques, such as a multilayer board with a
low-inductance ground plane, or star connect all ground
return paths back to the MAX5813/MAX5814/MAX5815
GND. Carefully layout the traces between channels to
reduce AC cross-coupling. Do not use wire-wrapped
boards and sockets. Use shielding to minimize noise immu-
nity. Do not run analog and digital signals parallel to one
another, especially clock signals. Avoid routing digital lines
underneath the MAX5813/MAX5814/MAX5815 package.
Definitions
Integral Nonlinearity (INL)
INL is the deviation of the measured transfer function
from a straight line drawn between two codes once offset
and gain errors have been nullified.
Differential Nonlinearity (DNL)
DNL is the difference between an actual step height and
the ideal value of 1 LSB. If the magnitude of the DNL P
1 LSB, the DAC guarantees no missing codes and is
monotonic. If the magnitude of the DNL R 1 LSB, the DAC
output may still be monotonic.
Offset Error
Offset error indicates how well the actual transfer function
matches the ideal transfer function. The offset error is
calculated from two measurements near zero code and
near maximum code.
Gain Error
Gain error is the difference between the ideal and the
actual full-scale output voltage on the transfer curve,
after nullifying the offset error. This error alters the slope
of the transfer function and corresponds to the same
percentage error in each step.
Zero-Scale Error
Zero-scale error is the difference between the DAC
output voltage when set to code zero and ground. This
includes offset and other die level nonidealities.
Full-Scale Error
Full-scale error is the difference between the DAC output
voltage when set to full scale and the reference voltage.
This includes offset, gain error, and other die level noni-
dealities.
Settling Time
The settling time is the amount of time required from the
start of a transition, until the DAC output settles to the new
output value within the converter’s specified accuracy.
Digital Feedthrough
Digital feedthrough is the amount of noise that appears
on the DAC output when the DAC digital control lines are
toggled.
Digital-to-Analog Glitch Impulse
A major carry transition occurs at the midscale point
where the MSB changes from low to high and all other
bits change from high to low, or where the MSB changes
from high to low and all other bits change from low to
high. The duration of the magnitude of the switching
glitch during a major carry transition is referred to as the
digital-to-analog glitch impulse.
The digital-to-analog power-up glitch is the duration of
the magnitude of the switching glitch that occurs as the
device exits power-down mode.
相關PDF資料
PDF描述
VE-262-IV-F4 CONVERTER MOD DC/DC 15V 150W
VE-262-IV-F3 CONVERTER MOD DC/DC 15V 150W
VE-262-IV-F2 CONVERTER MOD DC/DC 15V 150W
VE-261-IV-F4 CONVERTER MOD DC/DC 12V 150W
VE-261-IV-F3 CONVERTER MOD DC/DC 12V 150W
相關代理商/技術參數
參數描述
MAX5815AAUD+ 功能描述:數模轉換器- DAC 12-Bit 4Ch V DAC w/I2C Interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5815AAUD+T 功能描述:數模轉換器- DAC MAX5815 Eval Kit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5815AWC+T 功能描述:數模轉換器- DAC 4Ch 12Bit Voltage DAC with I2C RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5815BAUD+ 功能描述:數模轉換器- DAC MAX5815 Eval Kit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5815BAUD+T 功能描述:數模轉換器- DAC MAX5815 Eval Kit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*