- 您現在的位置：買賣IC網 > PDF目錄384686 > MAX537BEWE (MAXIM INTEGRATED PRODUCTS INC) Calibrated, Quad, 12-Bit Voltage-Output DACs with Serial Interface PDF資料下載
參數資料
| 型號： | MAX537BEWE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DAC |
| 英文描述： | Calibrated, Quad, 12-Bit Voltage-Output DACs with Serial Interface |
| 中文描述： | QUAD, SERIAL INPUT LOADING, 3 us SETTLING TIME, 12-BIT DAC, PDSO16 |
| 封裝： | 0.300 INCH, MS-013AA, SOIC-16 |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 361K |
| 代理商： | MAX537BEWE |
M
Using an AC Referenc e
In applications where the reference has AC signal compo-
nents, the MAX536/MAX537 have multiplying capability
within the reference input range specifications. Figure 12
shows a technique for applying a sine-wave signal to the
reference input where the AC signal is offset before being
applied to REFAB/REFCD. The reference voltage must
never be more negative than DGND.
The MAX536’s total harmonic distortion plus noise
(THD + N) is typically less than 0.012%, given a 5V
p-p
sig-
nal swing and input frequencies up to 35kHz, or given a
2V
p-p
swing and input frequencies up to 50kHz. The typi-
cal -3dB frequency is 700kHz as shown in the Typical
Operating Characteristics graphs.
For the MAX537, with an input signal amplitude of
0.85mV
p-p
, THD + N is typically less than 0.024% with a
5k
load in parallel with 100pF and input frequencies up to
100kHz, or with a 2k
load in parallel with 100pF and input
frequencies up to 95kHz.
Offsetting AGND
AGND can be biased from DGND to the reference voltage
to provide an arbitrary nonzero output voltage for a zero
input code (Figure 13). The output voltage V
OUTA
is:
V
OUTA
= V
BIAS
+ N
B
(V
IN)
where V
BIAS
is the positive offset voltage (with respect
to DGND) applied to AGND, and N
B
is the numeric
value of the DAC’s binary input code. Since AGND is
common to all four DACs, all outputs will be offset by
V
BIAS
in the same manner. As the voltage at AGND
increases, the DAC’s resolution decreases because its
full-scale voltage swing is effectively reduced. AGND
should not be biased more negative than DGND.
Power-S upply Considerations
On power-up, V
SS
should come up first, V
DD
next, then
REFAB or REFCD. If supply sequencing is not possible,
tie an external Schottky diode between V
SS
and AGND
as shown in Figure 14. On power-up, all input and DAC
registers are cleared (set to zero code) and SDO is in
Mode 0 (serial data is shifted out of SDO on the clock’s
rising edge).
For rated MAX536 performance, V
DD
should be 4V
higher than REFAB/REFCD and should be between
10.8V and 16.5V. When using the MAX537, V
DD
should
be at least 2.2V higher than REFAB/REFCD and should
be between 4.75V and 5.5V. Bypass both V
DD
and V
SS
with a 4.7
μ
F capacitor in parallel with a 0.1
μ
F capacitor
to AGND. Use short lead lengths and place the bypass
capacitors as close to the supply pins as possible.
Grounding and Layout Considerations
Digital or AC transient signals between AGND and
DGND can create noise at the analog outputs. Tie
AGND and DGND together at the DAC, then tie this
point to the highest quality ground available.
Good printed circuit board ground layout minimizes
crosstalk between DAC outputs, reference inputs, and
digital inputs. Reduce crosstalk by keeping analog
lines away from digital lines. Wire-wrapped boards are
not recommended.
Calibrated, Quad, 12-Bit
Voltage-Output DACs with S erial Interfac e
22
______________________________________________________________________________________
MAX536
MAX537
1N5817
3
4
V
SS
AGND
Figure 14. When V
SS
and V
DD
cannot be sequenced, tie a
Schottky diode between V
SS
and AGND.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX536BMDE | Calibrated, Quad, 12-Bit Voltage-Output DACs with Serial Interface |
| MAX537BMDE | Calibrated, Quad, 12-Bit Voltage-Output DACs with Serial Interface |
| MAX5383EZT-T | Low-Cost, Low-Power, 8-Bit DACs with 3-Wire Serial Interface in SOT23 |
| MAX5383 | Low-Cost, Low-Power, 8-Bit DACs with 3-Wire Serial Interface in SOT23 |
| MAX5383EUT-T | Low-Cost, Low-Power, 8-Bit DACs with 3-Wire Serial Interface in SOT23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX537BEWE+ | 功能描述:數模轉換器- DAC 12-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BEWE+T | 功能描述:數模轉換器- DAC 12-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BEWE-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX537BMDE | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5380LEUK | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。