- 您現在的位置：買賣IC網 > PDF目錄384684 > MAX5270AEMH (MAXIM INTEGRATED PRODUCTS INC) LJT 6C 6#20 PIN PLUG PDF資料下載
參數資料
| 型號： | MAX5270AEMH |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DAC |
| 英文描述： | LJT 6C 6#20 PIN PLUG |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 22 us SETTLING TIME, 13-BIT DAC, PQFP44 |
| 封裝： | MQFP-44 |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 251K |
| 代理商： | MAX5270AEMH |
M
Octal, 13-Bit Voltage-Output DAC
with Parallel Interface
______________________________________________________________________________________
11
Table 3. Analog Voltage vs. Digital Code
The output amplifier multiplies V
DAC
by 2, yielding an
output voltage range of 2
REF- to 2
REF+ (Figure
1). Further manipulation of the output voltage span is
accomplished by offsetting DUTGND. The output volt-
age of the MAX5270 is described by the following
equation:
(
where DATA is the numeric value of the DAC’s binary
input code, and DATA ranges from 0 (2
0
) to 8191
(2
13
- 1). The resolution of the MAX5270, defined as
1LSB, is described by the following equation:
(
Reference Selection
Since the MAX5270 has precision buffers on its refer-
ence inputs, the requirements for interfacing to these
inputs are minimal. Select a low-drift, low-noise refer-
ence within the recommended REF+ and REF- voltage
ranges. The MAX5270 does not require bypass capaci-
tors on its reference inputs. Add capacitors only if the
reference voltage source requires them to meet system
specifications.
Minimizing Output Glitch
The MAX5270’s internal deglitch circuitry is enabled on
the falling edge of
LD
. Therefore, to achieve optimum
performance, drive
LD
low after the inputs are either
latched or steady state. This is best accomplished by
having the falling edge of
LD
occur at least 50ns after
the rising edge of
CS
.
Power Supplies, Grounding,
and Bypassing
For optimum performance, use a multilayer PC board
with an unbroken analog ground. For normal operation,
connect the four DUTGND pins directly to the ground
plane. Avoid sharing the connections of these sensitive
pins with other ground traces.
As with any sensitive data-acquisition system, connect
the digital and analog ground planes together at a sin-
gle point, preferably directly underneath the MAX5270.
Avoid routing digital signals underneath the MAX5270
to minimize their coupling into the IC.
For normal operation, bypass V
DD
and V
SS
with 0.1μF
ceramic chip capacitors to the analog ground plane. To
enhance transient response and capacitive drive capa-
bility, add 10μF tantalum capacitors in parallel with the
ceramic capacitors. Note, however, that the MAX5270
does not require the additional capacitance for stability.
Bypass V
CC
with a 0.1μF ceramic chip capacitor to the
digital ground plane.
Power-Supply Sequencing
To guarantee proper operation of the MAX5270, ensure
that power is applied to V
DD
before V
SS
and V
CC
. Also
ensure that V
SS
is never more than 300mV above
ground. To prevent this situation, connect a Schottky
diode between V
SS
and the analog ground plane, as
shown in Figure 3. Do not power-up the logic input pins
before establishing the supply voltages. If this is not
possible and the digital lines can drive more than
10mA, place current-limiting resistors (e.g., 470
) in
series with the logic pins.
LSB
2 REF
REF
2
13
=
+
)
V
2 V
V
DATA
13
2
V
V
OUT
REF
REF
REF
OUTGND
=
)
+
+
INPUT CODE
0 0000 0000 0001
1 1111 1111 1111
0 1111 1111 1111
1 0000 0000 0000
0 0000 0000 0000
OUTPUT
VOLTAGE (V)
+0.001
+8.191
+4.095
+4.096
0
Note:
Output voltage is based on REF+ = +4.096V, REF- = 0V,
and DUTGND = 0.
GND
V
SS
SYSTEM GND
1N5817
V
SS
V
SS
Figure 3. Schottky Diode Between V
SS
and GND
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5270ACMH | Octal, 13-Bit Voltage-Output DAC with Parallel Interface |
| MAX5270 | Low Power 5V RS232 Dual Driver/Receiver with 0.1?μF Capacitors; Package: SO; No of Pins: 16; Temperature Range: -40?°C to 85?°C |
| MAX5270BEMH | Octal, 13-Bit Voltage-Output DAC with Parallel Interface |
| MAX529EWG | Octal, 8-Bit, Serial DACs with Output Buffer |
| MAX528-MAX529 | Octal, 8-Bit, Serial DACs with Output Buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5270AEMH-T | 制造商:Maxim Integrated Products 功能描述: |
| MAX5270AEMH-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX5270BCMH | 制造商:Maxim Integrated Products 功能描述:OCTAL, 13-BIT, VOLTAGE-OUTPUT DAC WITH PARALL - Bulk |
| MAX5270BEMH | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX527BCWG | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。