- 您現在的位置：買賣IC網 > PDF目錄383424 > MAX495 (Maxim Integrated Products, Inc.) High-Output RS-485 Transceiver 8-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | MAX495 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Output RS-485 Transceiver 8-SOIC -40 to 85 |
| 中文描述： | 單/雙/四路、微功耗、單電源、滿擺幅運算放大器 |
| 文件頁數： | 10/16頁 |
| 文件大小： | 230K |
| 代理商： | MAX495 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
M
S ingle/Dual/Quad, Mic ropower,
S ingle-S upply Rail-to-Rail Op Amps
10
______________________________________________________________________________________
MAX495
10k
1
5
NULL
V
EE
4
NULL
Figure 2. Offset Null Circuit
__________Applic ations Information
The dual MAX492, quad MAX494, and single MAX495
op amps combine excellent DC accuracy with rail-to-
rail operation at both input and output. With their preci-
sion performance, wide dynamic range at low supply
voltages, and very low supply current, these op amps
are ideal for battery-operated equipment and other low-
voltage applications.
Rail-to-Rail Inputs and Outputs
The MAX492/MAX494/MAX495’s input common-mode
range extends 0.25V
beyond
the positive and negative
supply rails, with excellent common-mode rejection.
Beyond the specified common-mode range, the out-
puts are guaranteed not to undergo phase reversal or
latchup. Therefore, the MAX492/MAX494/MAX495 can
be used in applications with common-mode signals at
or even beyond the supplies, without the problems
associated with typical op amps.
The MAX492/MAX494/MAX495’s output voltage swings
to within 50mV of the supplies with a 100k
load. This
rail-to-rail swing at the input and output substantially
increases the dynamic range, especially in low supply-
voltage applications. Figure 1 shows the input and out-
put waveforms for the MAX492, configured as a
unity-gain noninverting buffer operating from a single
+3V supply. The input signal is 3.0V
p-p
, 1kHz sinusoid
centered at +1.5V. The output amplitude is approxi-
mately 2.95V
p-p
.
Input Offset V oltage
Rail-to-rail common-mode swing at the input is obtained
by two complementary input stages in parallel, which
feed a folded cascaded stage. The PNP stage is active
for input voltages close to the negative rail, and the
NPN stage is active for input voltages close to the posi-
tive rail.
The offsets of the two pairs are trimmed; however, there
is some small residual mismatch between them. This
mismatch results in a two-level input offset characteris-
tic, with a transition region between the levels occurring
at a common-mode voltage of approximately 1.3V.
Unlike other rail-to-rail op amps, the transition region
has been widened to approximately 600mV in order to
minimize the slight degradation in CMRR caused by
this mismatch.
To adjust the MAX495’s input offset voltage (500μV max
at +25°C), connect a 10k
trim potentiometer between
the two NULL pins (pins 1 and 5), with the wiper con-
nected to V
EE
(pin 4) (Figure 2). The trim range of this
circuit is ±6mV. External offset adjustment is not avail-
able for the dual MAX492 or quad MAX494.
The input bias currents of the MAX492/MAX494/MAX495
are typically less than 50nA. The bias current flows into
the device when the NPN input stage is active, and it
flows out when the PNP input stage is active. To reduce
the offset error caused by input bias current flowing
through external source resistances, match the effec-
tive resistance seen at each input. Connect resistor R3
between the noninverting input and ground when using
V
IN
V
OUT
Figure 1. Rail-to-Rail Input and Output (Voltage Follower
Circuit, VCC = +3V, VEE= 0V)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX495CPA | High-Output RS-485 Transceiver 8-PDIP -40 to 85 |
| MAX495CSA | High-Output RS-485 Transceiver 8-PDIP -40 to 85 |
| MAX495EPA | High-Output RS-485 Transceiver 8-SOIC -40 to 85 |
| MAX495ESA | High-Output RS-485 Transceiver 8-SOIC -40 to 85 |
| MAX495MJA | High-Output RS-485 Transceiver 8-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4950ACTX+ | 功能描述:均衡器 Single PCIe Re-Driver RoHS:否 制造商:Texas Instruments |
| MAX4950ACTX+T | 功能描述:IC PCIE REDRIVER DUAL 36-TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,240 系列:GD 類型:收發器 驅動器/接收器數:3/5 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:20-DIP（0.300"，7.62mm） 供應商設備封裝:20-PDIP 包裝:管件 |
| MAX4950CTO+ | 功能描述:IC PCIE REDRIVER 3.3V 42TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:2,500 系列:- 類型:驅動器 驅動器/接收器數:4/0 規程:RS422 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| MAX4950CTO+T | 功能描述:IC PCIE REDRIVER 3.3V 42TQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,240 系列:GD 類型:收發器 驅動器/接收器數:3/5 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:20-DIP（0.300"，7.62mm） 供應商設備封裝:20-PDIP 包裝:管件 |
| MAX4951AECTP+ | 功能描述:緩沖器和線路驅動器 SATA I/II Bidirect Re-Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。