參數資料
型號: MAX5187BEEG
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: DAC
英文描述: 8-Bit, 40MHz, Current/Voltage-Output DACs
中文描述: PARALLEL, 8 BITS INPUT LOADING, 0.025 us SETTLING TIME, 8-BIT DAC, PDSO24
封裝: 0.150 INCH, 0.025 INCH PITCH, QSOP-24
文件頁數: 10/16頁
文件大?。?/td> 226K
代理商: MAX5187BEEG
M
8-Bit, 40MHz, Current/Voltage-Output DACs
10
______________________________________________________________________________________
PD
(POWER-DOWN SELECT)
DACEN
(DAC ENABLE)
POWER-DOWN MODE
OUTPUT STATE
0
0
Standby
MAX5187
MAX5190
Last state prior to standby mode
MAX5187
MAX5190
High-Z
AGND
0
1
Wake-Up
1
X
Shutdown
High-Z
AGND
Table 1. Power-Down Mode Selection
X = Don’t care
External Reference
To disable the MAX5187/MAX5190’s internal reference,
connect
REN
to DV
DD
. A temperature-stable external ref-
erence may now be applied to drive the REFO pin to set
the full-scale output (Figure 3). Choose a reference that
can supply at least 150μA to drive the bias circuit that
generates the cascode current for the current array. For
improved accuracy and drift performance, choose a volt-
age reference with a fixed output voltage, such as the
+1.2V, 25ppm/°C MAX6520 bandgap reference.
Standby Mode
To enter the lower power standby mode, connect the
digital inputs PD and DACEN to DGND. In standby,
both the reference and the control amplifier are active
with the current array inactive. To exit this condition,
DACEN must be pulled high with PD held at DGND.
Both the MAX5187 and MAX5190 typically require 50μs
to wake up and allow both the outputs and the refer-
ence to settle.
Shutdown Mode
For lowest power consumption, the MAX5187/MAX5190
provide a power-down mode in which the reference,
control amplifier, and current array are inactive and the
DAC’s supply current is reduced to 1μA. To enter this
mode, connect PD to DV
DD
. To return to active mode,
connect PD to DGND and DACEN to DV
DD
. About 50μs
are required for the parts to leave shutdown mode and
settle to their outputs’ values prior to shutdown.
Timing Information
Figure 4 shows a detailed timing diagram for the
MAX5187/MAX5190. With each high transition of the
clock, the input latch is loaded with the digital value set
by bits D7 through D0. The content of the input latch is
then shifted to the DAC register, and the output
updates at the rising edge of the next clock.
CLK
D0
D7
OUT
N - 1
N - 1
N
N
N + 1
N + 1
t
DS
t
DH
t
CH
t
CL
t
CLK
Figure 4. Timing Diagram
相關PDF資料
PDF描述
MAX5204 Low-Cost, Voltage-Output, 16-Bit DACs in UMAX
MAX5206ACUB Low-Cost, Voltage-Output, 16-Bit DACs in UMAX
MAX5206AEUB Low-Cost, Voltage-Output, 16-Bit DACs in UMAX
MAX5204ACUB Low-Cost, Voltage-Output, 16-Bit DACs in UMAX
MAX5204AEUB Low-Cost, Voltage-Output, 16-Bit DACs in UMAX
相關代理商/技術參數
參數描述
MAX5187BEEG+ 功能描述:數模轉換器- DAC 8-Bit High Speed DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5187BEEG+T 功能描述:數模轉換器- DAC 8-Bit High Speed DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5187BEEG-T 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5188 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual, 8-Bit, 40MHz, Current/Voltage, Alternate-Phase Output DACs
MAX5188_01 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual, 8-Bit, 40MHz, Current/Voltage,Alternate-Phase Output DACs