- 您現在的位置：買賣IC網 > PDF目錄383431 > MAX515CSA (MAXIM INTEGRATED PRODUCTS INC) 5V, Low-Power, Voltage-Output, Serial 10-Bit DACs PDF資料下載
參數資料
| 型號： | MAX515CSA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DAC |
| 英文描述： | 5V, Low-Power, Voltage-Output, Serial 10-Bit DACs |
| 中文描述： | SERIAL INPUT LOADING, 25 us SETTLING TIME, 10-BIT DAC, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 174K |
| 代理商： | MAX515CSA |
M
S ingle-S upply Linearity
As with any amplifier, the MAX504/MAX515’s output
buffer offset can be positive or negative. When the off-
set is positive, it is easily accounted for (Figure 10).
However, when the offset is negative, the buffer output
cannot follow linearly when there is no negative supply.
In that case, the amplifier output (VOUT) remains at
ground until the DAC voltage is sufficient to overcome
the offset and the output becomes positive.
Normally, linearity is measured after accounting for
zero error and gain error. Since, in single-supply opera-
tion, the actual value of a negative offset is unknown, it
cannot be accounted for during test. Additionally, the
output buffer amplifier exhibits a nonlinearity near-zero
output when operating with a single supply. To account
for this nonlinearity in the MAX504/MAX515, linearity
and gain error are measured from code 3 to code
1023. The output buffer’s offset and nonlinearity do not
affect monotonicity, and these DACs are guaranteed
monotonic starting with code zero. In dual-supply oper-
ation, linearity and gain error are measured from code
0 to 1023.
Power-S upply Bypassing and
Ground Management
Best system performance is obtained with printed cir-
cuit boards that use separate analog and digital
ground planes. Wire-wrap boards are not recommend-
ed. The two ground planes should be connected
together at the low-impedance power-supply source.
DGND and AGND should be connected together at the
chip. For the MAX504 in single-supply applications,
connect V
SS
to AGND at the chip. The best ground
connection may be achieved by connecting the DAC's
DGND and AGND pins together and connecting that
point to the system analog ground plane. If the DAC's
DGND is connected to the system digital ground, digi-
tal noise may get through to the DAC’s analog portion.
Bypass V
DD
(and V
SS
in dual-supply mode) with a
0.1μF ceramic capacitor connected between V
DD
and
AGND (and between V
SS
and AGND). Mount it with
short leads close to the device. Ferrite beads may also
be used to further isolate the analog and digital power
supplies.
Figures 11a and 11b illustrate the grounding and
bypassing scheme described.
S aving Power
When the DAC is not being used by the system, mini-
mize power consumption by setting the appropriate
code to minimize load current. For example, in bipolar
mode, with a resistive load to ground, set the DAC
code to mid-scale (see Table 3). If there is no output
load, minimize internal loading on the reference by set-
ting the DAC to all 0s (on the MAX504, use
CLR
).
Under this condition, REFIN is high impedance and the
op amp operates at its minimum quiescent current.
Due to these low currents, the output settling time for a
zero input code typically increases to 60μs (100μs
max).
5V, Low-Power, Voltage-Output,
S erial 10-Bit DACs
12
______________________________________________________________________________________
Figure 8. Bipolar Configuration (-2.048V to +2.048V Output)
Table 3. Bipolar (Offset Binary) Code
Table (-V
REFIN
to +V
REFIN
Output)
33μF
REFIN
REFOUT
AGND
DGND
BIPOFF
RFB
VOUT
V
OUT
-5V
+5V
MAX504
INPUT*
OUTPUT
1111
1111
11(00)
1000
0000
01(00)
1000
0000
00(00)
0111
1111
11(00)
0000
0000
01(00)
0000
0000
00(00)
(+V
REFIN
) 512
(+V
REFIN
) 512
(-V
REFIN
) 512
(-V
REFIN
) 512
0V
(-V
REFIN
) 512= -V
REFIN
* Write 10-bit data words with two sub-LSB 0s because the
DAC input latch is 12 bits wide.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX515ESA | 5V, Low-Power, Voltage-Output, Serial 10-Bit DACs |
| MAX5160MEUA | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5161 | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5160-MAX5161 | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5160 | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX515CSA+ | 功能描述:數模轉換器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX515CSA+T | 功能描述:數模轉換器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX515CSA-T | 功能描述:數模轉換器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX515EPA | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX515EPA+ | 功能描述:數模轉換器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。