- 您現在的位置：買賣IC網 > PDF目錄385532 > MAX5120AEEE (MAXIM INTEGRATED PRODUCTS INC) Circular Connector; No. of Contacts:18; Series:MS27466; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:15-18 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | MAX5120AEEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DAC |
| 英文描述： | Circular Connector; No. of Contacts:18; Series:MS27466; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:15-18 RoHS Compliant: No |
| 中文描述： | SERIAL INPUT LOADING, 20 us SETTLING TIME, 12-BIT DAC, PDSO16 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-16 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 288K |
| 代理商： | MAX5120AEEE |
M
(MAX5120) and Figure 3b (MAX5121) to achieve these
adjustments. Connect a 33nF capacitor from REFADJ
to AGND to establish low-noise operation of the DAC.
Larger capacitor values may be used, but will result in
increased start-up delay. The time constant (
τ
) for the
start-up delay is determined by the REFADJ input
impedance of 4k
and C
REFADJ
:
τ
= 4k
·
C
REFADJ
External Referenc e
An external reference may be applied to the REF pin.
Disable the internal reference by pulling REFADJ to
V
DD
. This allows an external reference signal (AC- or
DC-based) to be fed into the REF pin. For proper oper-
ation,
do not
exceed the input voltage range limits of
0V to (V
DD
- 1.4V) for V
REF
.
Determine the output voltage using the following equa-
tion (REFADJ = V
DD
; OS = AGND):
V
OUT
= [V
REF
·
(NB / 4096)]
·
1.6384V/V
where NB is the numeric value of the MAX5120/
MAX5121 input code (0 to 4095), V
REF
is the external
reference voltage, and 1.6384V/V is the gain of the
internal output amplifier. The REF pin has a minimum
input resistance of 40k
and is code-dependent.
Output Amplifier
The output amplifier of the MAX5120/MAX5121
employs a trimmed resistor-divider to set a gain of
+1.6384V/V and minimize the gain error. With its on-
board laser-trimmed +1.25V reference and the output
buffer gain, the MAX5121 achieves a full-scale output
of +2.0475V, while the MAX5120 provides a +4.095V
full-scale output with a +2.5V reference.
The output amplifier has a typical slew rate of 0.6V/μs
and settles to ±0.5LSB within 20μs, with a load of 5k
in parallel with 100pF. Loads less than 1k
may result
in degraded performance.
The OS pin may be used to adjust the output offset volt-
age. For instance, to achieve a +1V offset, apply
-1.566V (Offset = -[Output Buffer Gain - 1]
·
V
OS
) to OS
to produce an output voltage range from +1V to (1V +
V
REF
·
1.6384V/V). Note that the DAC’s output range is
still limited by the maximum output voltage specifica-
tion.
Power-Down Mode
The MAX5120/MAX5121 feature software- and hard-
ware-programmable (PD pin) shutdown modes that
reduce the typical supply current to 3μA. To enter soft-
ware shutdown mode, program the control sequence
for the DAC as shown in Table 1.
In shutdown mode, the amplifier output becomes high
impedance and the serial interface remains active.
Data in the input registers is saved, allowing the
MAX5120/MAX5121 to recall the output state prior to
entering shutdown when returning to normal operation
mode. To exit shutdown mode, load both input and
DAC registers simultaneously or update the DAC regis-
ter from the input register. When returning from shut-
down mode, wait 2ms for the reference to settle. When
using an external reference, the DAC requires only
20μs for the output to stabilize.
+3V /+5V, 12-Bit, S erial Voltage-Output DACs
with Internal Referenc e
10
______________________________________________________________________________________
REFADJ
+5V
90k
100k
400k
33nF
MAX5120
REFADJ
+3V
15k
100k
400k
33nF
MAX5121
Figure 3a. MAX5120 Reference Adjust Circuit
Figure 3b. MAX5121 Reference Adjust Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5121AEEE | +3V/+5V, 12-Bit, Serial Voltage-Output DACs with Internal Reference |
| MAX5120 | +3V/+5V, 12-Bit, Serial Voltage-Output DACs with Internal Reference |
| MAX5120-MAX5121 | +3V/+5V, 12-Bit, Serial Voltage-Output DACs with Internal Reference |
| MAX5120BEEE | +3V/+5V, 12-Bit, Serial Voltage-Output DACs with Internal Reference |
| MAX5121BEEE | +3V/+5V, 12-Bit, Serial Voltage-Output DACs with Internal Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5120AEEE+ | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5120AEEE+T | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5120AEEE-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5120BEEE | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5120BEEE+ | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。