- 您現在的位置：買賣IC網 > PDF目錄383424 > MAX5037 (Maxim Integrated Products, Inc.) VRM 9.0.Dual-Phase.Parallelable.Average Current-Mode Controller PDF資料下載
參數資料
| 型號： | MAX5037 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | VRM 9.0.Dual-Phase.Parallelable.Average Current-Mode Controller |
| 中文描述： | VRM 9.0、雙相、可并聯、平均電流模式控制器 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 608K |
| 代理商： | MAX5037 |
E
The Power Circuit Topology
Among the several power topologies available, the sin-
gle-transistor forward topology offers a simple and low-
cost solution and provides very good efficiency
throughout the operating power range. However, this
topology requires a transformer reset winding connect-
ed to pins T1
–
3 and T1
–
4 (Figure 7). The forward con-
verter was chosen because it offers higher power den-
sity and higher efficiency than a flyback converter at
these power levels. Transformer T1 provides 1500V iso-
lation between primary and secondary. Efficiency is fur-
ther improved by powering the control circuit from a
primary bias winding (T1
–
5, T1
–
6, Figure 7) after initial
startup. A 250kHz switching frequency was selected to
allow small form-factor transformer, inductor, and out-
put capacitors.
Key Operating Waveforms
Key operating waveforms are always useful in under-
standing the operation of switching power supplies. A
10
×
oscilloscope probe is necessary for effective prob-
ing. A digital scope is very useful in capturing startup
sequences. However, extreme caution should be exer-
cised when probing live power supplies. For example,
shorting the drain-source terminals of Q1 while power is
applied is sure to produce a big spark and may dam-
age the EV kit.
Figure 5 shows the drain-to-source waveform of Q1.
Notice the leading-edge voltage spike. This is a result
of the energy stored in transformer T1
’
s leakage induc-
tance.
Figure 6 shows the voltage at the output of the sec-
ondary rectifier (cathode of D4).
PC Board Layout and
Component Placement
As with any other switching power supply, component
placement is very important. Because of the primary-to-
secondary isolation, the primary and secondary
grounds are separated. Figure 10 clearly shows the
separation on both sides of the PC board. The layout of
the board can be changed to accommodate different
footprints. Also, the power MOSFET and output rectifier
should be mounted on a heatsink for best thermal man-
agement. In this implementation, both of these compo-
nents are on the noncomponent side of the board, with
their tabs mounted to the heatsink plate.
The critical layout considerations are as follows:
Distance from the secondary transformer leads to
diode D4 should be kept to a minimum. This will
improve EMI as well as the effective available
power transfer.
Bypass capacitors C4, C5, and C6 should be as
close as possible to T1
–
1.
The PC board trace connecting T1
–
2 to the drain of
Q1 should be as short as possible.
The current-sense resistor R6 should be as close as
possible to the source of Q1 and should return with a
very short trace either to the ground plane or to the
negative lead of bypass capacitors C4, C5, and C6.
The gate-drive loop, consisting of pin 14 of
MAX5003, R16, Q1, R6, and pin 13 of the
MAX5003, must be kept as short as possible and
preferably routed over a ground plane.
Relevant trace spacing (relating to trace creepage)
must be observed according to applicable safety
agency guidelines.
MAX5003-50W Evaluation Kit
4
_______________________________________________________________________________________
MAX5003 fig05
50V/div
V
D
(
400ns/div
Figure 5. Drain-Source Voltage Waveform
MAX5003 fig06
200ns/div
5V/div
Figure 6. Waveform at Cathode of D4
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5041 | Dual-Phase.Parallelable.Average Current-Mode Controllers |
| MAX5042EVKIT | Evaluation Kit for the MAX5042 |
| MAX5051EVKIT | Evaluation Kit for the MAX5051 |
| MAX508BEPP | 12-Bit Digital-to-Analog Converter |
| MAX508BMJP | 12-Bit Digital-to-Analog Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5037A | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:VRM 9.0/VRM 9.1. Dual-Phase. Parallelable. Average-Current-Mode Controller |
| MAX5037AEMH | 功能描述:電流型 PWM 控制器 VRM 9/9.1 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX5037AEMH+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5037AEMH-T | 功能描述:電流型 PWM 控制器 VRM 9/9.1 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX5037AETH | 功能描述:電流型 PWM 控制器 VRM 9/9.1 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。