- 您現在的位置：買賣IC網 > PDF目錄383426 > MAX5022EPA (MAXIM INTEGRATED PRODUCTS INC) Current-Mode PWM Controllers for Isolated Power Supplies PDF資料下載
參數資料
| 型號： | MAX5022EPA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Current-Mode PWM Controllers for Isolated Power Supplies |
| 中文描述： | 0.25 A SWITCHING CONTROLLER, 290 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, MS-095-AH, DIP-8 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 240K |
| 代理商： | MAX5022EPA |
85VAC (corresponding to 120VDC) to the 24V wakeup
level results in a resistor value of about 1M
. If we
assume R
S
values between 750k
and 1M
, then at
the high-line voltage of 265VAC (corresponding to
374VDC) power dissipation will be between 140mW to
190mW. A single 1/4W resistor or a series combination
of two 1/4W resistors is adequate.
Undervoltage Lockout (UVLO)
The device will attempt to start when V
IN
exceeds the
UVLO threshold of 24V. During startup, the UVLO cir-
cuit keeps the CPWM comparator, ILIM comparator,
oscillator, and output driver shut down to reduce cur-
rent consumption
(Functional Diagram)
. Once V
IN
reaches 24V, the UVLO circuit turns on both the CPWM
and ILIM comparators, as well as the oscillator, and
allows the output driver to switch. If V
IN
drops below
10V, the UVLO circuit will shut down the CPWM com-
parator, ILIM comparator, oscillator, and output driver
returning the MAX5021/MAX5022 to the startup mode.
N-Channel MOSFET Switch Driver
The NDRV pin drives an external N-channel MOSFET.
The NDRV output is supplied by the internal regulator
(V
CC
), which is internally set to approximately 9V. For
the universal input voltage range, the MOSFET used
must be able to withstand the DC level of the high-line
input voltage plus the reflected voltage at the primary
of the transformer. For most applications that use the
discontinuous flyback topology, this requires a MOS-
FET rated at 600V. NDRV can source/sink 150mA/
250mA peak current, thus select a MOSFET that will
yield acceptable conduction and switching losses.
Internal Oscillator
The internal oscillator switches at 1.048MHz and is
divided down to 262kHz by two D flip-flops. The
MAX5021 inverts the Q output of the last D flip-flop to
provide a duty cycle of 50% (Figure 3). The MAX5022
performs a logic NAND operation on the Q outputs of
both D flip-flops to provide a duty cycle of 75%.
Optocoupler Feedback
The MAX5021/MAX5022 do not include an internal error
amplifier and are recommended for use in optocoupler
feedback power supplies. Isolated voltage feedback is
achieved by using an optocoupler and a shunt regula-
tor as shown in the
Typical Operating Circuit
. The out-
put voltage set point accuracy is a function of the
accuracy of the shunt regulator and resistor divider.
When a TLV431 shunt regulator is used for output volt-
age regulation, the output voltage is set by the ratio of
R4 and R5 (Figure 1). Output voltage is given by the
following equation:
where V
REF
= 1.24V for the TLV431.
During normal operation, the optocoupler feedback pin
(OPTO) is pulled up through a 6.2k
resistor to the
internal supply voltage of 5.25V. When the device is in
UVLO, OPTO is disconnected from the 5.25V regulator
and connected to ground
(Functional Diagram).
This
helps initial startup by reducing the current consump-
tion of the device.
Current Limit
The current limit is set by a current sense resistor, R
CS
,
connected between the source of the MOSFET and
ground. The CS input has a voltage trip level (V
CS
) of
600mV. Use the following equation to calculate the
value of R
CS
:
where I
PRI
is the peak current in the primary that flows
through the MOSFET. When the voltage produced by
this current through the current sense resistor exceeds
the current-limit comparator threshold, the MOSFET dri-
ver (NDRV) will quickly terminate the current ON-cycle,
typically within 60ns. In most cases a small RC filter will
be required to filter out the leading-edge spike on the
sense waveform. Set the corner frequency at a
few MHz.
Applications Information
Universal Off-Line Power Supply
Figure 1 shows the design of a 5V/1A isolated power
supply capable of operating from a line voltage of
85VAC to 265VAC. This circuit is implemented in the
MAX5022EVKIT.
R
V
I
PRI
CS
CS
=
V
V
R
R
OUT
REF
=
×
+
1
4
5
M
Current-Mode PWM Controllers for Isolated
Power Supplies
_______________________________________________________________________________________
7
OSCILLATOR
1.048MHz
D
Q
Q
D
Q
Q
262kHz WITH 50%
(MAX5021)
262kHz WITH 75%
(MAX5022)
Figure 3. Internal Oscillator
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5022EUA | Current-Mode PWM Controllers for Isolated Power Supplies |
| MAX5022EUT | Current-Mode PWM Controllers for Isolated Power Supplies |
| MAX5022EVKIT | Current-Mode PWM Controllers for Isolated Power Supplies |
| MAX5038AEAI25 | Circular Connector; No. of Contacts:18; Series:MS27473; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:14; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:14-18 RoHS Compliant: No |
| MAX5038AEAI33 | JT 37C 37#22D SKT WALL RECP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5022EPA+ | 功能描述:電流型 PWM 控制器 for Isolated Power Supplies RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX5022ESA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5022ETT+T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| MAX5022EUA | 功能描述:電流型 PWM 控制器 for Isolated Power Supplies RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX5022EUA+ | 功能描述:電流型 PWM 控制器 for Isolated Power Supplies RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。