- 您現在的位置：買賣IC網 > PDF目錄385532 > MAX492 (Maxim Integrated Products, Inc.) Dual, Micropower, Single-Supply Rail-to-Rail Op Amps(輸入失調電壓500μV,單電源滿量程運放) PDF資料下載
參數資料
| 型號： | MAX492 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual, Micropower, Single-Supply Rail-to-Rail Op Amps(輸入失調電壓500μV,單電源滿量程運放) |
| 中文描述： | 單/雙/四路、微功耗、單電源、滿擺幅運算放大器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 224K |
| 代理商： | MAX492 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
M
S ingle/Dual/Quad, Mic ropower,
S ingle-S upply Rail-to-Rail Op Amps
12
______________________________________________________________________________________
bility is maintained with up to 400pF of output capaci-
tance. If the output sources either more or less current,
stability is increased. These devices perform well with a
1000pF pure capacitive load (Figure 5). Figure 6 shows
the performance with a 500pF load in parallel with vari-
ous load resistors.
To increase stability while driving large capacitive
loads, connect a pull-up resistor at the output to
decrease the current that the amplifier must source. If
the amplifier is made to sink current rather than source,
stability is further increased.
Frequency stability can be improved by adding an out-
put isolation resistor (R
S
) to the voltage follower circuit
(Figure 7). This resistor improves the phase margin of
the circuit by isolating the load capacitor from the op
amp’s output. Figure 8a shows the MAX492 driving
10,000pF (R
L
≥
100k
), while Figure 8b adds a 47
isolation resistor.
Because the MAX492/MAX494/MAX495 have excellent
stability, no isolation resistor is required, except in the
most demanding applications. This is beneficial
because an isolation resistor would degrade the low-
frequency performance of the circuit.
10
μ
s/div
V
50mV/div
V
50mV/div
MAX49_
V
OUT
V
IN
C
L
R
S
10
μ
s/div
V
50mV/div
V
50mV/div
10
μ
s/div
V
50mV/div
V
50mV/div
Figure 7. Capacitive-Load Driving Circuit
Figure 6c. MAX492 Voltage Follower with 500pF Load—
R
L
=
∞
Figure 6a. MAX492 Voltage Follower with 500pF Load—
R
L
= 5k
Figure 6b. MAX492 Voltage Follower with 500pF Load—
R
L
= 20k
相關PDF資料 |
PDF描述 |
|---|---|
| MAX494 | Quad, Micropower, Single-Supply Rail-to-Rail Op Amps(輸入失調電壓500μV,單電源滿量程運放) |
| MAX5003 | High-Voltage PWM Power-Supply Controller |
| MAX5003CEE | High-Voltage PWM Power-Supply Controller |
| MAX5003CSE | High-Voltage PWM Power-Supply Controller |
| MAX5003EEE | High-Voltage PWM Power-Supply Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4920BETD+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4920BETD+T | 功能描述:電池管理 Battery Power-Up Logic RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX4921BETD+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4921BETD+T | 功能描述:電池管理 Battery Power-Up Logic RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX4924ELT+T | 功能描述:開關變換器、穩壓器與控制器 Overvoltage Protector RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。