- 您現在的位置：買賣IC網 > PDF目錄383410 > MAX456CPL (MAXIM INTEGRATED PRODUCTS INC) 8 x 8 Video Crosspoint Switch PDF資料下載
參數資料
| 型號： | MAX456CPL |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 8 x 8 Video Crosspoint Switch |
| 中文描述： | 8-CHANNEL, CROSS POINT SWITCH, PDIP40 |
| 封裝： | PLASTIC, DIP-40 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 99K |
| 代理商： | MAX456CPL |
M
8 x 8 Video Crosspoint S witc h
4
_______________________________________________________________________________________
______________________________________________________________Pin Desc ription
Note 1:
Buffer inputs are internally grounded with a 1000 or 1001 command from the D3-D0 lines. AGND must be at 0.0V since the
gain setting resistors of the buffers are internally tied to AGND.
PIN
NAME
FUNCTION
—
1, 12, 23, 34
N.C.
No connect. Not internally connected.
Parallel Data Bit D1 when SER/P——–= 0V. Serial Output for cascading
multiple parts when SER/P——–= 5V.
Parallel Data Bit D0 when SER/P——–= 0V. A Serial Input when
SER/P——–= 5V.
1
2
D1/SER OUT
2
3
D0/SER IN
3, 4, 6
4, 5, 7
A2, A1, A0
Output Buffer Address Lines
5, 7, 9, 11,
13, 15, 17, 19
6, 8, 10, 13,
15, 17, 19, 21
IN0–IN7
Video lnput Lines
8
9
LOAD
Asynchronous control line. When LOAD = 1, all the 400
internal active
loads are on. When LOAD = 0, external 400
loads must be used. The
buffers MUST have a resistive load to maintain stability.
Digital Ground Pins. Both DGND pins must have the same potential and
be bypassed to AGND. DGND should be within ±0.3V of AGND.
10, 12
11, 14
DGND
14
16
EDGE/–————
When this control line is high, the 2nd-rank registers are loaded with the
rising edge of the LATCH line. If this control line is low, the 2nd-rank reg-
isters are transparant when LATCH is low, passing data directly from the
1st-rank registers to the decoders.
16, 26, 40
18, 29, 44
V+
All V+ pins must be tied to each other and bypassed to AGND
separately (Figure 2).
18
20
SER/P——–
5V = 32-Bit Serial, 0V = 7-Bit Parallel
20, 34
22, 38
V-
Both V- pins must be tied to each other and bypassed to AGND
separately (Figure 2).
WRITE in the serial mode, shifts data in. In the parallel mode, WR loads
data into the 1st-rank registers. Data is latched on the rising edge.
If EDGE/–————= 5V, data is loaded from the 1st-rank registers to the 2nd-
rank registers on the rising edge of LATCH. If EDGE/–————= 0V, data is
loaded while LATCH = 0V. In addition, data is loaded during the execution
of parallel-mode functions 1011 through 1110, or if LATCH = 5V during the
execution of the parallel-mode "software-LATCH" command (1111).
21
24
WR
22
25
LATCH
23
26
C—
–——p—E————e. When–—= 0V and CE = 5V, the WR line is enabled.
Chip Enable. When –—= 0V and CE = 5V, the WR line is enabled.
24
27
CE
25, 27, 29, 31,
33, 35, 37, 39
28, 30, 32, 35,
37, 39, 41, 43
OUT7-OUT0
Output Buffers 7-0 (Note 1)
28, 30, 32
31, 33, 36
AGND
Analog Ground must be at 0.0V since the gain resistors of the buffers are
tied to these 3 pins.
Parallel Data Bit D3 when SER/ –——–= 0V. When D3 = 0V, D0-D2 specifies
the input channel to be connected to buffer. When D3 = 5V, then D0-D2
Parallel Data Bit D2 when SER/–——–= 0V. Not used when
SER/–——–= 5V.
36
40
D3
38
42
D2
DIP
PLCC
相關PDF資料 |
PDF描述 |
|---|---|
| MAX456CQH | 8 x 8 Video Crosspoint Switch |
| MAX456EQH | 8 x 8 Video Crosspoint Switch |
| MAX456EPL | 8 x 8 Video Crosspoint Switch |
| MAX456EJL | 8 x 8 Video Crosspoint Switch |
| MAX4570CAI | Serially Controlled, Dual 4x2, Clickless Audio/Video Analog Crosspoint Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX456CPL+ | 功能描述:視頻開關 IC 8x8 Crosspoint Video Switch RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX456CQH | 制造商:Maxim Integrated Products 功能描述: |
| MAX456CQH+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX456CQH+D | 功能描述:視頻開關 IC RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX456CQH+TD | 功能描述:視頻開關 IC RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。