參數資料
型號: MAX4509EPE
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 運動控制電子
英文描述: Replaced by TMS320VC5509A : Digital Signal Processor 144-LQFP
中文描述: DUAL 4-CHANNEL, SGL ENDED MULTIPLEXER, PDIP16
封裝: 0.300 INCH, PLASTIC, MS-001AA, DIP-16
文件頁數: 10/16頁
文件大小: 288K
代理商: MAX4509EPE
M
When the NO_ voltage goes beyond supply rails (fault
condition), the NO_ input becomes high impedance
regardless of the switch state or load resistance. When
power is removed, and the fault protection is still in
effect, the NO_ terminals are a virtual open circuit. The
fault can be up to ±40V, with V+ = V- = 0. If the switch
is on, the COM_ output current is furnished from the V+
or V- pin by “booster” FETs connected to each supply
pin. These FETs can source or sink up to 10mA.
The COM_ pins are not fault protected. If a voltage
source is connected to any COM_ pin, it should be lim-
ited to the supply voltages. Exceeding the supply volt-
age will cause high currents to flow through the ESD
protection diodes, damaging the device (see Absolute
Maximum Ratings).
Figure 1 shows the internal construction, with the ana-
log signal paths shown in bold. A single normally open
(NO) switch is shown. The analog switch is formed by
the parallel combination of N-channel FET N1 and P-
channel FET P1 which are driven on and off simultane-
ously, according to the input fault condition and the
logic level state.
NO_ Input V oltage
The maximum allowable input voltage for safe opera-
tion depends on whether supplies are on or off and the
load configuration at the COM output. If COM is re-
ferred to a voltage other than ground, but within the
supplies, V
NO_
may range higher or lower than the sup-
plies provided the absolute value of
V
NO_
- V
COM_
is
less than 40V. For example, if the load is referred to
+10V at COM_, then the NO_ voltage range can be
from +50V to -30V. As another example, if the load is
connected to -10V at COM_, the NO_ voltage range is
limited to -50V to +30V.
If the supplies are ±15V and COM is referenced to
ground through a load, the maximum NO_ voltage is
±25V. If the supplies are off and the COM output is ref-
erenced to ground, the maximum NO_ voltage is ±40V.
Fault-Protec ted, High-Voltage
S ingle 8-to-1/Dual 4-to-1 Multiplexers
10
______________________________________________________________________________________
NORMALLY OPEN SWITCH CONSTRUCTION
COM_
P2
MAX4508
MAX4509
P1
N1
ON
LOW
FAULT
HIGH
FAULT
V+
NO_
A-
GWD
ESOCODE
V-
N2
Figure 1. Functional Diagram
相關PDF資料
PDF描述
MAX4509ESE Fault-Protected, High-Voltage Single 8-to-1/Dual 4-to-1 Multiplexers
MAX4508EAE Fault-Protected, High-Voltage Single 8-to-1/Dual 4-to-1 Multiplexers
MAX4508MJE Fault-Protected, High-Voltage Single 8-to-1/Dual 4-to-1 Multiplexers
MAX4509CAE Fault-Protected, High-Voltage Single 8-to-1/Dual 4-to-1 Multiplexers
MAX4509MJE Fault-Protected, High-Voltage Single 8-to-1/Dual 4-to-1 Multiplexers
相關代理商/技術參數
參數描述
MAX4509ESE 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX4509ESE+ 功能描述:多路器開關 IC 4:1 2Ch Fault Prtctd Analog MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX4509ESE+T 功能描述:多路器開關 IC 4:1 2Ch Fault Prtctd Analog MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX4509ESE-T 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX4509ESE-W 制造商:Maxim Integrated Products 功能描述:16 PINS N.SO PKG - Rail/Tube