<ins id="5k3cr"><sub id="5k3cr"><tfoot id="5k3cr"></tfoot></sub></ins>
<thead id="5k3cr"><legend id="5k3cr"><code id="5k3cr"></code></legend></thead>
    • <thead id="5k3cr"><xmp id="5k3cr"><code id="5k3cr"></code></xmp></thead>
      <ins id="5k3cr"><sup id="5k3cr"></sup></ins>
      參數資料
      型號: MAX4505EUA
      廠商: Maxim Integrated Products
      文件頁數: 7/8頁
      文件大小: 0K
      描述: IC SIGNAL LINE PROTECTOR 8-UMAX
      產品培訓模塊: Lead (SnPb) Finish for COTS
      Obsolescence Mitigation Program
      標準包裝: 50
      類型: 過壓防護
      應用: 控制系統
      安裝類型: 表面貼裝
      封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
      供應商設備封裝: 8-uMAX
      包裝: 管件
      Fault Protection with Power Off
      When power is off (i.e., V+ = V- = 0), the protector is a
      virtual open circuit. The output stays at 0 with up to
      ±40V applied to the input.
      Fault Protection with Power On
      A fault condition exists when the voltage on AIN
      exceeds either supply rail. This definition is valid when
      power is on or off, as well as during all states while
      power ramps up or down.
      Applications Information
      Supplying Power Through External ICs
      The MAX4505 has low supply current (<250A), which
      allows the supply pins to be driven by other active cir-
      cuitry instead of connected directly to the power
      sources. In this configuration, the part can be used as a
      driven fault-protected switch with V+ or V- used as the
      control pins. For example, with the V- pin grounded, the
      output of a CMOS gate can drive the V+ pin to turn the
      device on and off. Ensure that the driving source(s)
      does not drive the V+ pin more negative than the V- pin.
      Protector as Circuit Elements
      Figure 3 shows a MAX4505 used in front of a MAX338
      unprotected 1-to-8 multiplexer. With supplies at ±15V,
      VAOUT of the MAX4505 clamps to ±15V and VOUT of
      the MAX338 goes to ±14V. With supplies off, VAOUT
      goes to 0 even though the input remains at ±25V.
      Multiplexer and Demultiplexer
      The MAX4505 can be used in series with the output of a
      MAX4508 (1-to-8 multiplexer) to act as multiplexer or
      demultiplexer. The MAX4508 is a fault-protected multi-
      plexer whose inputs are designed to interface with harsh
      environments; however, its common output is not fault
      protected if connected to outside signals (i.e., demulti-
      plexer use). If the common output can see fault signals,
      then it needs to be protected, and the MAX4505 can be
      added to provide complete protection.
      As seen in Figure 4, the signal input can now be put
      into pin 3 of the MAX4505 (new common output for sys-
      tem), and outputs can be taken at MAX4508 pins 4 to
      7, and 9 to 12. This is the classic demultiplexer opera-
      tion. This system now has full protection on both of the
      multiplexers’ inputs and outputs.
      Measuring Path Resistance
      Measuring path resistance requires special techniques,
      since path resistance varies dramatically with the AIN
      and AOUT voltages relative to the supply voltages. Do
      not use conventional ohmmeters. Their applied voltage
      and currents are usually unpredictable. The true resis-
      MAX4505
      Fault-Protected, High-Voltage,
      Signal-Line Protector
      _______________________________________________________________________________________
      7
      MAX4505
      ROUT
      VIN
      AIN
      V-
      V+
      AOUT
      Figure 2. Application Circuit
      16
      15
      14
      13
      12
      11
      10
      9
      1
      2
      3
      4
      5
      6
      7
      8
      MAX338
      -15V
      1
      2
      8
      7
      +15V
      +25V
      3
      4
      6
      5
      MAX4505
      A1
      A2
      GND
      V+
      NO5
      NO6
      NO7
      NO8
      AO
      EN
      V-
      OV
      +5V
      +3V
      +15V
      -5V
      NO3
      NO1
      NO2
      NO4
      VOUT
      Figure 3. Protecting a MAX338 with a MAX4505
      16
      15
      14
      13
      12
      11
      10
      9
      1
      2
      3
      4
      5
      6
      7
      8
      MAX4508
      -15V
      1
      2
      8
      7
      +15V
      NEW COM
      3
      4
      6
      5
      MAX4505
      A1
      A2
      GND
      V+
      NO5
      NO6
      NO7
      NO8
      AO
      EN
      V-
      O
      +5V
      +3V
      +15V
      -15V
      NO3
      NO1
      NO2
      NO4
      COM
      Figure 4. Demultiplexer Application Using MAX4505
      with MAX4508
      相關PDF資料
      PDF描述
      MAX4507EAP IC SIGNAL LINE PROTECTOR 20-SSOP
      MAX4508EPE+ IC MULTIPLEXER 8X1 16DIP
      MAX4513ESE IC SWITCH QUAD SPST 16SOIC
      MAX4515ESA IC SWITCH SPST 8SOIC
      MAX4517CSA IC SWITCH SPST 8SOIC
      相關代理商/技術參數
      參數描述
      MAX4505EUA+T 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
      MAX4505EUA-T 功能描述:電流和電力監控器、調節器 RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
      MAX4505EUK 制造商:Maxim Integrated Products 功能描述:FAULT-PROTECTED HIGH-VOLTAGE SIGN - Rail/Tube
      MAX4505EUK+ 制造商:Maxim Integrated Products 功能描述:FAULT PROTECTED 5PIN SOT-23 - Rail/Tube
      MAX4505EUK+T 功能描述:模擬開關 IC Fault-Protected Signal-Line Protectr RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16