- 您現在的位置：買賣IC網 > PDF目錄11050 > MAX4502CPA (Maxim Integrated Products)IC SWITCH SPST 8DIP PDF資料下載
參數資料
| 型號： | MAX4502CPA |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH SPST 8DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 功能： | 開關 |
| 電路： | 1 x SPST- NC |
| 導通狀態(tài)電阻： | 250 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2 V ~ 12 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
MAX4501/MAX4502
Low-Voltage, SPST, CMOS Analog Switches
6
_______________________________________________________________________________________
Applications Information
Power-Supply Considerations
The MAX4501/MAX4502 are constructed like most
CMOS analog switches, except they have only two sup-
ply pins: V+ and GND. V+ and GND drive the internal
CMOS switches and set the analog voltage limits of the
switch. Reverse ESD-protection diodes are internally
connected between each analog signal pin and both
V+ and GND. One of these diodes conducts if any ana-
log signal exceeds V+ or GND. During normal opera-
tion, these and other reverse-biased ESD diodes leak,
forming the only current drawn from V+ or GND.
Virtually all the analog leakage current comes from the
ESD diodes. Although the ESD diodes on a given sig-
nal pin are identical and therefore fairly well balanced,
they are reverse biased differently. Each is biased by
either V+ or GND and the analog signal. This means
their leakages will vary as the signal varies. The differ-
ence in the two diode leakages to the V+ and GND
pins constitutes the analog signal-path leakage current.
All analog leakage current flows between each pin and
one of the supply terminals, not to the other switch ter-
minal. This is why both sides of a given switch can
show leakage currents of the same or opposite polarity.
There is no connection between the analog-signal
paths and V+ or GND.
V+ and GND also power the internal logic and logic-
level translators, and set the input logic limits. The
logic-level translators convert the logic levels to
switched V+ and GND signals to drive the analog sig-
nal gates. This drive signal is the only connection
between the logic supplies (and signals) and the ana-
log supplies. COM, NO, and NC pins have ESD-protec-
tion diodes to V+ and GND.
The logic-level thresholds are CMOS/TTL compatible
when V+ is +5V. As V+ rises, the threshold increases
slightly. When V+ reaches +12V, the logic-level thresh-
old is about 3V—above the TTL guaranteed high-level
minimum of 2.8V, but still compatible with CMOS out-
puts.
Do not connect the MAX4501/MAX4502’s V+ pin to
+3V and then connect the logic-level pins to TTL
logic-level signals. TTL levels can exceed +3V and
violate the absolute maximum ratings, damaging
the part and/or external circuits.
High-Frequency Performance
In 50
systems, signal response is reasonably flat up
to 250MHz (see Typical Operating Characteristics).
Above 20MHz, the on-response has several minor
peaks that are highly layout dependent. The problem is
not in turning the switch on; it’s in turning it off. The off-
state switch acts like a capacitor and passes higher
frequencies with less attenuation. At 10MHz, off-isola-
tion is about -60dB in 50
systems, decreasing
approximately 20dB per decade as frequency increas-
es. Higher circuit impedances also cause off-isolation
to decrease. Adjacent channel attenuation is about 3dB
above that of a bare IC socket, and is due entirely to
capacitive coupling.
______________________________________________________________Pin Description
Note: NO, NC, and COM pins are identical and interchangeable. Any may be considered as an input or an output; signals pass
equally well in both directions.
FUNCTION
NAME
MAX4501
MAX4502
SO/DIP
SC70-5/SOT23-5
SO/DIP
SC70-5/SOT23-5
Positive Supply-Voltage Input (analog and digital)
PIN
1
COM
Analog Switch Common Terminal
2, 3, 5
—
2, 3, 5
—
N.C.
No Connection. Not internally connected.
4
5
V+
6
4
6
4
IN
Digital Control Input
7
3
7
3
GND
Ground
8
2
—
NO
Analog Switch (normally open)
—
8
2
NC
Analog Switch (normally closed)
5
4
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4501EPA | IC SWITCH SPST 8DIP |
| MAX4501CSA | IC SWITCH SPST 8SOIC |
| MAX4066AEPD | IC SWITCH QUAD SPST 14DIP |
| MAX4053ESE | IC MULTIPLEXER TRPL 2X1 16SOIC |
| MAX4053EPE | IC MULTIPLEXER TRPL 2X1 16DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4502CSA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4502CSA+T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4502CSA-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX4502CUK | 制造商:Maxim Integrated Products 功能描述:NORMALLY CLOSED LOW-VOLTAGE SPST - Cut Tape Product |
| MAX4502CUK+T | 功能描述:模擬開關 IC Low-Voltage SPST CMOS Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發(fā)布緊急采購，3分鐘左右您將得到回復。