- 您現在的位置：買賣IC網 > PDF目錄384673 > MAX4432EUA (MAXIM INTEGRATED PRODUCTS INC) Dual-Supply, 180MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps PDF資料下載
參數資料
| 型號： | MAX4432EUA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Dual-Supply, 180MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps |
| 中文描述： | OP-AMP, 5000 uV OFFSET-MAX, 180 MHz BAND WIDTH, PDSO8 |
| 封裝： | MICRO MAX PACKAGE-8 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 748K |
| 代理商： | MAX4432EUA |
Detailed Description
The MAX4430
–
MAX4433 are wide-bandwidth, ultra-low-
distortion, voltage-feedback amplifiers. The MAX4430/
MAX4432 are internally compensated for unity gain.
The MAX4431/MAX4433 are internally compensated for
gains of +2V/V or greater.
These amplifiers have ultra-fast 37ns (MAX4430/
MAX4432) 16-bit settling times, 100dB SFDR at 1MHz,
and 4Vp-p output swing with minimum 110dB open-
loop gain.
High-Speed ADC Input Driver Application
The MAX4430
–
MAX4433 op amps are ideal for driving
high-speed 14- to 16-bit ADCs. In most cases, these
ADCs operate with a charge balance scheme, with
capacitive loads internally switched on and off from the
input. The driver used must withstand these changing
capacitive loads while holding the signal amplitude sta-
bility consistent with the ADC
’
s resolution and, at the
same time, have a frequency response compatible with
the sampling speed of the ADC (Figure 1).
Inverting and Noninverting Configurations
The circuits typically used for the inverting and non-
inverting configurations of the MAX4430
–
MAX4433 are
shown in Figures 2a and 2b. The minimum uncondition-
ally stable gain values are 1 for the MAX4430/MAX4432
and 2 for the MAX4431/MAX4433. Use care in selecting
the value for the resistor marked R
S
in both circuits.
From dynamic stability considerations (based on the
part
’
s frequency response and the input capacitance of
the MAX4430
–
MAX4433), the maximum recommended
value for R
S
is 500
. In general, lower R
S
values will
yield a higher bandwidth and better dynamic stability,
at the cost of higher power consumption, higher power
dissipation in the IC, and reduced output drive avail-
ability. For a minimum R
S
value, take into consideration
that the current indicated as I
F
is supplied by the output
stage and must be discounted from the maximum out-
put current to calculate the maximum current available
to the load. I
F
can be found using the following equa-
tion:
I
F
= V
IN(MAX)
/ R
S
If DC thermal stability is an important design concern,
the Thevenin resistance seen by both inputs at DC
must be balanced. This includes the resistance of the
signal source and termination resistors if the amplifier
signal input is fed from a transmission line. The capaci-
tance associated with the feedback resistors must also
be considered as a possible limitation to the available
bandwidth or to the dynamic stability. Only resistors
with small parallel capacitance specifications should
be considered.
Applications Information
Layout and Power-Supply Bypassing
The MAX4430
–
MAX4433 have wide bandwidth and
consequently require careful board layout. To realize
the full AC performance of these high-speed amplifiers,
pay careful attention to power-supply bypassing and
board layout. The PC board should have a large low-
impedance ground plane that is as free of voids as
possible. Do not use commercial breadboards. Keep
signal lines as short and straight as possible. Observe
high-frequency bypassing techniques to maintain the
M
Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
_______________________________________________________________________________________
9
+V
CC
-V
EE
HIGH-SPEED
14/16-BIT ADC
Figure 1. Typical Application Circuit
V
OUT
V
IN
R
S
R
F
I
F
R
F
R
S
V
OUT
V
IN
=
A = 1 +
Figure 2a. Noninverting Configuration
- R
F
R
S
V
OUT
V
IN
V
OUT
V
IN
R
B
R
F
R
S
I
F
=
A =
Figure 2b. Inverting Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4433EUA | Dual-Supply, 180MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps |
| MAX4455 | Triple Differential Transceivers 20-SOIC -40 to 85 |
| MAX4455ECQ | Triple Differential Transceivers 20-SOIC -40 to 85 |
| MAX445CPG | Triple Differential Transceivers 20-SSOP -40 to 85 |
| MAX4504EPA | Low-Voltage, Dual-Supply, SPST, CMOS Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4432EUA+ | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4432EUA+T | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4432EUA-T | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4433ESA | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4433ESA-T | 功能描述:運算放大器 - 運放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。