- 您現在的位置：買賣IC網 > PDF目錄384671 > MAX4370ESA (MAXIM INTEGRATED PRODUCTS INC) Current-Regulating Hot-Swap Controller with DualSpeed/BiLevel Fault Protection PDF資料下載
參數資料
| 型號： | MAX4370ESA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Current-Regulating Hot-Swap Controller with DualSpeed/BiLevel Fault Protection |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | 0.150 INCH, MS-012AA, SOIC-8 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 226K |
| 代理商： | MAX4370ESA |
M
Using the MAX 4370 on the Bac kplane
The MAX4370 can be used on the backplane to regu-
late current upon insertion of a removable card. This
allows multiple cards with different input capacitance to
be inserted into the same slot even if the card doesn’t
have on-board hot-swap protection.
The MAX4370 current-limiting feature is active during
the start-up period set by CTIM. The start-up period
can be triggered if V
IN
is connected to ON through a
trace on the card. Once t
START
has expired (timed out),
the load capacitance has to be charged or a fault con-
dition is detected. To ensure start-up with a fixed CTIM,
t
START
has to be longer than the time required to
charge the board capacitance. The maximum load
capacitance is calculated as follows:
C
BOARD
< t
START
·
I
FAST,SET
/ V
IN
Input T ransients
The voltage at V
IN
must be above the UVLO during
inrush and fault conditions. When a short condition
occurs on the board, the fault current can be higher
than the fast comparator current limit. The gate voltage
is discharged immediately, but note that the MOSFET is
not completely off until V
GS
< V
TH
. If the main system
power supply collapses below UVLO, the MAX4370 will
force the device to restart once the supply has recov-
ered. The main system power supply must be able to
deliver this fault current without excessive voltage drop.
The MOSFET is turned off in a very short time; there-
fore, the resulting di/dt can be considerable. The back-
plane delivering the power to the external card must
have a fairly low inductance to limit the voltage tran-
sients caused by the removal of a fault.
MOS FET T hermal Considerations
During normal operation, the MOSFET dissipates little
power; it is fully turned on and its R
DS(ON)
is minimal.
The power dissipated in normal operation is P
D
=
(I
LOAD)2
·
R
DS(ON)
. A considerable amount of power is
dissipated during the turn-on and turn-off transients.
The design must take into consideration the worst-case
scenario of a continuous short-circuit fault present on
the board. Two cases must be considered:
1) The single turn-on with the device latched after a
fault.
2) An external circuit forces a continuous automatic
retry after the fault.
MOSFET manufacturers typically include the package
normalized transient thermal resistance (r
θ
J A
(t) or
r
θ
J C
(t)), which is determined by the start-up time and
the retry duty cycle (d = t
START
/ t
RETRY
). The following
equation is used to calculate the required transient
thermal resistance:
R
θ
J A
(t) = (T
J ,MAX
- T
A
) / P
D,MAX
(t)
where P
DMAX
(t) = V
IN
·
I
FAULT
and the resulting R
θ
J A
=
R
θ
J A
(t) / r
θ
J A
(t). R
θ
J A
is the thermal resistance deter-
mined with a continuous load and by the layout or
heatsink.
Layout Considerations
To take full advantage of the switch response time to an
output fault condition, it is important to keep all traces
as short as possible and to maximize the high-current
trace dimensions to reduce the effect of undesirable
parasitic inductance. Place the MAX4370 close to the
card’s connector. Use a ground plane to minimize its
impedance and inductance.
Minimize the current-sense resistor trace length
(<10mm), and ensure accurate current sensing with
Kelvin connections (Figure 12).
When the output is short circuited, the voltage drop
across the external MOSFET becomes large. Hence,
the power dissipation across the switch increases, as
does the die temperature. An efficient way to achieve
good power dissipation on a surface-mount package is
to lay out two copper pads directly under the package
on both sides of the board. Connect the two pads to
the ground plane through vias, and use enlarged cop-
per mounting pads on the top side of the board.
Current-Regulating Hot-S wap Controller with
DualS peed/BiLevel Fault Protec tion
14
______________________________________________________________________________________
V
IN
V
IN
ON
BACKPLANE
MAX4370
VSEN
GATE
CTIM
C
BOARD
V
OUT
REMOVABLE CARD
WITH NOHOT-INSERTION
PROTECTION
Figure 11. Using the MAX4370 on the Backplane
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4370 | Current-Regulating Hot-Swap Controller with DualSpeed/BiLevel Fault Protection |
| MAX4373 | Low-Cost, Micropower, High-Side Current-Sense Amplifier Comparator Reference ICs |
| MAX4375 | Low-Cost, Micropower, High-Side Current-Sense Amplifier Comparator Reference ICs |
| MAX4373FESA | Low-Cost, Micropower, High-Side Current-Sense Amplifier Comparator Reference ICs |
| MAX4373FEUA | Low-Cost, Micropower, High-Side Current-Sense Amplifier Comparator Reference ICs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4370ESA+ | 功能描述:熱插拔功率分布 Current-Regulating Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX4370ESA+T | 功能描述:熱插拔功率分布 Current-Regulating Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX4370ESA-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX4372FEBT | 制造商:Maxim Integrated Products 功能描述:UCSP/SOT23, MICROPOWER, HIGH-SIDE CURRENT-SENSE AMP - Rail/Tube |
| MAX4372FEBT+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。