- 您現在的位置：買賣IC網 > PDF目錄10348 > MAX4364ESA+T (Maxim Integrated Products)IC AMP AUDIO PWR 1.4W MONO 8SOIC PDF資料下載
參數資料
| 型號： | MAX4364ESA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 1.4W MONO 8SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | AB 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 1.4W x 1 @ 8 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 特點： | 消除爆音，短路保護和熱保護，關閉 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 8-SOIC |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 包裝： | 帶卷 (TR) |
MAX4364/MAX4365
The increase in power delivered by the BTL configura-
tion directly results in an increase in internal power dis-
sipation over the single-ended configuration. The
maximum power dissipation for a given VCC and load is
given by the following equation:
If the power dissipation for a given application exceeds
the maximum allowed for a given package, reduce
VCC, increase load impedance, decrease the ambient
temperature or add heat sinking to the device. Large
output, supply, and ground PC board traces improve
the maximum power dissipation in the package.
Thermal-overload protection limits total power dissipa-
tion in the MAX4364/MAX4365. When the junction tem-
perature exceeds +160°C, the thermal protection
circuitry disables the amplifier output stage. The ampli-
fiers are enabled once the junction temperature cools
by 15°C. This results in a pulsing output under continu-
ous thermal overload conditions as the device heats
and cools.
The MAX4365 TDFN package features an exposed
thermal pad on its underside. This pad lowers the ther-
mal resistance of the package by providing a direct
heat conduction path from the die to the PC board.
Connect the exposed thermal pad to circuit ground by
using a large pad, ground plane, or multiple vias to the
ground plane.
Efficiency
The efficiency of the MAX4364/MAX4365 is calculated
by taking the ratio of the power delivered to the load to
the power consumed from the power supply. Output
power is calculated by the following equations:
where VPEAK is half the peak-to-peak output voltage. In
BTL amplifiers, the supply current waveform is a full-
wave rectified sinusoid with the magnitude proportional
to the peak output voltage and load. Calculate the sup-
ply current and power drawn from the power supply by
the following:
The efficiency of the MAX4364/MAX4365 is:
The device efficiency values in Table 1 are calculated
based on the previous equation and do include the
effects of quiescent current. Note that efficiency is low
at low output-power levels, but remains relatively con-
stant at normal operating, output-power levels.
Component Selection
Gain-Setting Resistors
External feedback components set the gain of both
devices. Resistors RF and RIN (see Typical Application
Circuit/Functional Diagram) set the gain of the amplifier
as follows:
Optimum output offset is achieved when RF = 20k.
Vary the gain by changing the value of RIN. When using
the MAX4364/MAX4365 in a high-gain configuration
(greater than 8V/V), a feedback capacitor may be
required to maintain stability (see Figure 2). CF and RF
limit the bandwidth of the device, preventing high-fre-
quency oscillations. Ensure that the pole created by CF
and RF is not within the frequency band of interest.
Input Filter
The input capacitor (CIN), in conjunction with RIN forms
a highpass filter that removes the DC bias from an
incoming signal. The AC-coupling capacitor allows the
amplifier to bias the signal to an optimum DC level.
Assuming zero source impedance, the -3dB point of
the highpass filter is given by:
Choose RIN according to the Gain-Setting Resistors
section. Choose CIN such that f-3dB is well below the
lowest frequency of interest. Setting f-3dB too high
affects the low-frequency response of the amplifier. Use
capacitors whose dielectrics have low-voltage coeffi-
=
3
1
2
dB
IN IN
RC
π
A
R
VD
F
IN
=×
2
η
π
==
P
PR
V
OUT
IN
OUT L
CC
2
PV
V
R
IN
CC
PEAK
L
=
2
π
I
V
R
CC
PEAK
L
=
2
π
P
V
R
OUT
PEAK
L
=
2
P
V
R
DISS MAX
CC
L
() =
2
π
1.4W and 1W, Ultra-Small, Audio Power
Amplifiers with Shutdown
10
______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2436-1IGN | IC CONV A/D 16B 2CH DIFF 16SSOP |
| LTC1199LCMS8#PBF | IC ADC 10BIT 210KHZ W/SD 8-MSOP |
| MAX9724AETC+T | IC AMP AUDIO .045W STER 12TQFN |
| MAX9724BETC+T | IC AMP AUDIO .045W STER 12TQFN |
| LTC1199LCMS8 | IC ADC 10BIT 210KHZ W/SD 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4364EVKIT | 功能描述:音頻放大器 Evaluation Kit for the MAX4364 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX4365EGA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4365ETA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4365ETA+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4365ETA+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。